+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Bought some "lumber" today.. (/showthread.php?tid=7337511)
RE: Bought some "lumber" today.. - bandit571 - 03-17-2018
Have to wait until 29 Mar 18 , as that is when i go over there..Picture of the sliding dovetail joint?
[attachment=9317]
Beads are done on the four pieces of the face frame..
[attachment=9318]
Dig a few holes..
[attachment=9319]
So these will fit..
[attachment=9320]
Like this..
[attachment=9321]
Bookcase's face frame is in the clamps.....
Top was cut to width earlier today. Need to attach it and the back panel...maybe tomorrow?
Stay tuned
RE: Bought some "lumber" today.. - bandit571 - 03-17-2018
A plywood back was cut to fit, used it to square the case, and installed the back. Top was radius cut on the front corners
[attachment=9337]
And a cove detail added to the underside.
[attachment=9338]
Counter-bores and pilot holes drilled, screws to attach the top to the case. Plugs made, and installed
[attachment=9339]
Will wait until morning to trim these flush. Set the bookcase unit onto the base unit for the night
[attachment=9340]
Install the face frame in the morning? Maybe start on a door?
Stay tuned
RE: Bought some "lumber" today.. - hbmcc - 03-18-2018
Looking good and nice coverage!
However, don't make this a going business. You started the cookup/project one month ago, February 18. Today is the 18th, also.
RE: Bought some "lumber" today.. - bandit571 - 03-18-2018
Imagine getting paid by the hour.....
Face frame and top are installed
[attachment=9358]
Plugs are all cleaned off...
[attachment=9359]
Got a start on the door that goes in the opening..
[attachment=9360]
Got to about here.
[attachment=9361]
Even set up the plough plane
[attachment=9362]
And started to check a few boards to make sure I could do a panel glue up, to make a raised panel for the door....
About three pieces are too short.....need to got to the Green BORG and buy ONE MORE BOARD
Back was getting stiff, almost 4 hours IN the shop, today. I think that will do, for one day.
Need to plough a few grooves to house the panel..tomorrow. Stay tuned....
(ps: there are some people out there, that take a YEAR to build a workbench....
)
RE: Bought some "lumber" today.. - Arlin Eastman - 03-18-2018
I like the idea of the dovetail in there. It will never pull out from the sides anyway.
RE: Bought some "lumber" today.. - bandit571 - 03-19-2018
A trip to the Blue BORG today....needed a 1 x8 x 4'......didn't find any, there was 6-footers....found some good 1 x 4 x 4' boards...two of those were just a dollar more than the single 1 x 8 x 6', and the two were wider than the one....then a nap while the Boss shopped at Wall E World...
Mondays, shop is usually closed...too many "bad" things happen in the shop on Mondays
Should be able to get a glue up done in the morning, and get some grooves done. By Friday, I hope to be adding the finish..I hope
Stay tuned, almost done with this project
RE: Bought some "lumber" today.. - bandit571 - 03-20-2018
ok....Mondays...gotta love them...the 1 x 4 x 4' boards? Turned out to be 1 x 6 x 4' boards...need to wear my glasses, I guess.
Ripped the fancy boards to width....wasn't a good cut..too much wave going on.
[attachment=9386]
Used the Disston to crosscut the "new" boards for length..
[attachment=9387]
Jointed the new boards' edge with a #7c the other two? First a jack plane to wipe out the high spots, then this
[attachment=9388]
#8 to joint the edges. Got all 8 edges done ( whew
) to where there was no gaps. Spread a bead of glue, moosh a board back and forth, until it sticks.....repeat for the other two...then add a few clamps... [attachment=9389]
Added a couple cauls on the ends to align the ends straight
[attachment=9390]
By this time the back was acting up,
all I have to do now, is wait on the glue to cure...then make this into the raised panel for the door...Maybe by the weekend, I can try to get a finish on this?
Stay tuned..
RE: Bought some "lumber" today.. - bandit571 - 03-21-2018
Panel has been "raised", frame fitted..
[attachment=9404]
The only difference between the way Paul Sellers and I do a raised panel..I lay the panel flat on the bench..Same planes, though
[attachment=9405]
At least for the end grain bevels Long grain was done with a jack plane. Ran a Wards 78 around on the back of the panel...same as the front, I do the end grain first, then the edge grain....tends to erase any blowouts. Door is now sitting in the clamps, waiting on the glue to cure
[attachment=9406]
Added a caul on each end, to keep things flat..
[attachment=9407]
Maybe tomorrow, I can install the door ( I hate hinges) and a small drawer that sits between the two units. Then see about a finish?
Figure IF I can get it looking too good to paint....
RE: Bought some "lumber" today.. - bandit571 - 03-22-2018
Just a teaser...
[attachment=9413]
Test fitted to find which end was "up"
[attachment=9414]
Added a couple hinges, making sure to "clock" the screws
[attachment=9415]
Added a wooden knob, and a brass Hook & Eye latch...
Need to build a skinny drawer to fill the "gap" between the two cases. Add the cleats to attach the top to the base....and start the finishing..
Might just do.....stay tuned
RE: Bought some "lumber" today.. - bandit571 - 03-23-2018
Skinny drawer is built, cleats installed, first coat of Golden Oak stain applied...PIP, anyone?
[attachment=9429]
Skinny drawer, dovetailed to match this larger drawer..
[attachment=9430]
Skinny drawer goes under the Bookcase..
[attachment=9431]
Bookcase is designed to be removable, and uses a pair of cleats to install..
[attachment=9432]
They also act as drawer guides for the skinny drawer...so..over all picture?
[attachment=9433]
Took just over 1/2 a pint of stain....hands still smell like it
Waiting on the stain to stop smelling the place up, might be dry enough to add the Amber Shellac top coats...?
Two bottom shelves get folding baskets in them...2 per shelf. Just about done with this project...stay tuned...may even post the finished cabinet when done and dry..