+- Woodnet Forums (https://www.forums.woodnet.net)
+-- Thread: wood filler (/showthread.php?tid=7370032)
wood filler - Gregor1 - 07-27-2022
Maybe the experts don't need it, but I use it. I have been using Elmers wood filler, because that's the only thing my local store sells, but it seems no matter how good I put the cap back on, once the tube is opened, it dries up. Do you have a favorite brand of wood filler?
Thanks Greg
RE: wood filler - Cabinet Monkey - 07-27-2022
(07-27-2022, 06:02 AM)Gregor1 Wrote: Maybe the experts don't need it, but I use it. I have been using Elmers wood filler, because that's the only thing my local store sells, but it seems no matter how good I put the cap back on, once the tube is opened, it dries up. Do you have a favorite brand of wood filler ?
Timbermate is my go to.
RE: wood filler - jteneyck - 07-27-2022
(07-27-2022, 07:30 AM)Cabinet Monkey Wrote: Timbermate is my go to.
Same. Never goes bad.
John
RE: wood filler - Rob Young - 07-27-2022
(07-27-2022, 07:30 AM)Cabinet Monkey Wrote: Timbermate is my go to.
Depends on application but this and "GoodFilla". Both are available on Amazon and I've found them to be interchangeable except that colors aren't matched.
You can use either as a pore filler during finishing too. I've experimented with plaster of paris as a pore filler and it's worked great. I've had some test pieces (flat sawn red oak and ash) hanging around for almost 4 years (2018) and no signs of filler popping out of the grain. P-of-P takes color very well so it becomes invisible. Did similar with RockHard putty and it has also been fine.
RE: wood filler - rwe2156 - 07-27-2022
Timbermate. If it dries out just add a little water. Big gaps take 2-3 coats b/c of shrinkage. Can take a while to dry.
When I need something to dry quick I like Famowood, use a MinWax plastic wood, both are acetone based and dry out quickly. Once they get dry enough they're done.
Goodfilla also but it does shrink in spite of the label says.
On bigger projects or repair I use Bondo and glazing putty.
RE: wood filler - KC - 07-27-2022
When I use filler (as infrequently as possible) I use what I think is Elmer's in a small square tub. Keep the lid on it and it'll be good for a long time. If it starts to harden up, you can soften it up with water.
Burn in sticks and wood - Bill Tindall - 07-27-2022
For small holes I used burn in sticks. Sometimes I carve the hole into a shape that looks more like a color variation in the wood or grain. These sticks can be blended to alter the color of the individual stick.
I also use pieces of wood from the scraps that match color and grain. A filler piece can be carved and mashed into the hole with glue and a clamp. Something the hole has to be carved. The repair is hard to see when luck prevails.
RE: wood filler - Bill Wilson - 07-29-2022
(07-27-2022, 07:30 AM)Cabinet Monkey Wrote: Timbermate is my go to.
^^^^
This
Significantly better than any of the "off the shelf" stuff you find at the Big Box.
RE: wood filler - Howard Pollack - 07-29-2022
I usually use fine sawdust mixed with whatever finish I will be using. No problem with incompatibility and the color match is most often very good. Burn-in sticks (colored shellac), as Bill suggests, are also excellent. -Howard
RE: wood filler - alanealane - 07-31-2022
(07-27-2022, 06:02 AM)Gregor1 Wrote: Maybe the experts don't need it, but I use it. I have been using Elmers wood filler, because that's the only thing my local store sells, but it seems no matter how good I put the cap back on, once the tube is opened, it dries up. Do you have a favorite brand of wood filler?
Thanks Greg
I use the Elmer's filler in a tube too. Try putting a little water in the cap and then threading it back onto the tip. The water will keep air from getting to the filler in the tip and will slightly mix with the filler at the very tip and keep it soft.