#28
on rounding bowl blanks.  He says he doesn't do it on bandsaws because they're not really designed for cutting wet, thick wood.  He has a point there.  In this video he cuts the log in half to create the bowl blanks, then takes them straight to the lathe.  I at least will knock the corners off.  My lathe is smaller and I get nervous spinning big pieces.  

Lyle on Chainsaw Use for Woodturning.mp4 - YouTube

Reply

#29
(12-21-2021, 11:47 AM)crokett™ Wrote: on rounding bowl blanks.  He says he doesn't do it on bandsaws because they're not really designed for cutting wet, thick wood.  He has a point there.  In this video he cuts the log in half to create the bowl blanks, then takes them straight to the lathe.  I at least will knock the corners off.  My lathe is smaller and I get nervous spinning big pieces.  

Lyle on Chainsaw Use for Woodturning.mp4 - YouTube

Won't be round after it's roughed wet and cures, anyway.  If it clears the ways, it's good enough.
Better to follow the leader than the pack. Less to step in.
Reply

#30
(12-22-2021, 05:36 AM)MichaelMouse Wrote: Won't be round after it's roughed wet and cures, anyway.  If it clears the ways, it's good enough.

That’s the other reason for me to knock corners off.  With a 12” swing I need to get it close to be able to get it to clear the ways.  I’ve thought about riser blocks.

Reply
#31
I don't have a nice supply of freshly cut logs to make bowl blanks from, so most all of my bowl blanks are cured and dried wood. Not a challenge for my band saw. It's not the band saw that's the problem with green wood. It's the bandsaw blade. If you're wanting to cut green wood on the bandsaw, you need a blade designed to do that. Some sappy woods I'd never ever cut on a bandsaw while green, though. Almond is one of those. When green, it's so sappy, the sap coats the blade, things heat up, and then you've pretty much ruined your blade.
Still Learning,

Allan Hill
Reply
#32
I don't have a nice supply of freshly cut logs to make bowl blanks from, so most all of my bowl blanks are cured and dried wood. Not a challenge for my band saw. It's not the band saw that's the problem with green wood. It's the bandsaw blade. If you're wanting to cut green wood on the bandsaw, you need a blade designed to do that. They are thicker than a normal blade, have a lower tpi and a wider kerf to clear the gullets. I remember Ron Herman in a class about saws at one of the Woodworking In America conferences talking about why a normal saw blade geometry doesn't work well in green wood. As the saw cuts, it heats up the wood. The moisture in the wood causes the wood to expand, which closes the kerf, thus binding the saw. Wide, deep gullets with a lower tpi and bigger set mitigate this problem.

Some sappy woods I'd never ever cut on a bandsaw while green, though. Almond is one of those. When green, it's so sappy, the sap coats the blade, things heat up, and then you've pretty much ruined your blade.

I also disagree with his claim that the bandsaw was not designed to cut thick wood. If that were the case, there sure are a lot of people making shop cut veneer who are violating his principle.

Not disparaging Lyle as a turner. He's one of the greats. And what works for him is fine. I did get a little nervous seeing him split that log with the chains so close to the frame of the WorkMate.
Still Learning,

Allan Hill
Reply

#33
(12-22-2021, 10:41 AM)AHill Wrote: I also disagree with his claim that the bandsaw was not designed to cut thick wood.  If that were the case, there sure are a lot of people making shop cut veneer who are violating his principle.

You missed a key adjective -   cutting wet, thick wood
Reply

#34
(12-22-2021, 03:29 PM)Wipedout Wrote: You missed a key adjective -   cutting wet, thick wood

Lots of bandmills putting that to the challenge.
Better to follow the leader than the pack. Less to step in.
Reply
#35
Yes you are correct however he's talking about home band saws

It's his opinion. Take it or leave it
Reply
#36
on cutting the corners he shown me how fast he can round off the edges faster then a bandsaw can cut them plus he told me i needed the practice anyway.

I do cut alot of the corners to use them for the fireplace later but if i am in a rush I just turn them off.

I can turn a half log to round in less then 10 minutes.  One other thing about cutting corners is less shavings.  It sure was nice of him stopping in three times to show me and the others how to use the tools properly
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Reply
#37
Octagons maybe. Mostly squares.

The corners come off pretty fast!
VH07V  
Reply
Interesting Take from Lyle Jamieson


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.