Shoulder and cheek same
#11
When cutting tenons, why can’t the shoulder and cheek cuts be the same depth?
Bill
Reply
#12
Not quite sure what you're meaning here. The cuts setting the length of the tenon would be the same on all sides. The cuts setting the removing the waste on the four sides would be deep enough to do just that. Said another way four cuts would be the same and two each of the other four cuts would be the same. Of course all that depends on the type tenon you are cutting.
There is no such thing as too much horsepower, free lunch or spare change ~ anonymous

87% of people say their mental health is good to excellent. The rest are sane enough to know they are lying. ~ anonymous
Reply
#13
I've wondered the same thing watching videos -- they often will cut the cheeks to a different depth than the shoulders.

Seems like an extra step to me.
"Truth is a highway leading to freedom"  --Kris Kristofferson

Wild Turkey
We may see the writing on the wall, but all we do is criticize the handwriting.
(joined 10/1999)
Reply
#14
First, definitions. Mine anyhow. Borrowing conventional nomenclature from a 2x4, a finished tenon on it will have 4 surfaces parallel with the 2x4. What I call the cheek will be the “flat” surface. The shoulder will be on the “edge”. Some would call what stops the rail from going further into the mortise, structural shoulder and cosmetic shoulder. Whatever!!

I cut tenons on a table saw with a dado blade. Why can’t I leave the blade at the same height roll the rail for each cut?
Reply
#15
After some thought, not my long suit, for a 3/4 " rail having the rail tight to the top of the post/leg, that 3/16" of material left on the top of the leg after the mortise might want to kick out, not to mention challenge its structural integrity.
Reply
#16
GEB said:


When cutting tenons, why can’t the shoulder and cheek cuts be the same depth?
Bill




The stock thickness of the mortise determines the thickness of the tenon. The cheek cuts are usually thinner than the shoulder cuts for that reason.Example, a stretcher is 3" wide and 3/4" thick. A single tenon may have a width (shoulder) 2" and 1/2" thick. The mortise would have 1/8" walls. This is an extreme example but I think you may understand it better now.
Sometimes wide tenons are divided up into several small ones. Then the cheek and shoulder can be the same with spaces between them. With the above example you could make the tenons 1/2 x1/2 x length.Then this could give you two tenons 1/4" from each end of the mortise and a 1/2" gap in the middle.

mike
Reply
#17
If I'm understanding your question the cheeks and shoulders could be the same depth but the cheeks will probably be much rougher than one would want.
Awwwwww!  Did I DO THAT?  Yep, doggone it, musta been me.
Reply
#18


this is one good reason setting the tenon lower strengthens the joint exponentially



and in the top drawing above the haunch fills a groove cut through which simplifies the groove adds some glue surface area and fills the gap
Let us not seek the Republican Answer , or the Democratic answer. Let us not seek to fix the blame for the past. Let us accept our own responsibility for the future  John F. Kennedy 



Reply
#19
AspenII said:


If I'm understanding your question the cheeks and shoulders could be the same depth but the cheeks will probably be much rougher than one would want.




Using a dado set this would be true. Using a saw blade then minimum 6 cuts, more for other type joints but the surfaces will be much smoother. Voice of experience here.
There is no such thing as too much horsepower, free lunch or spare change ~ anonymous

87% of people say their mental health is good to excellent. The rest are sane enough to know they are lying. ~ anonymous
Reply
#20
I guess they could be. I think the reason mortises are laid out that way is to leave enough stock above the tenon so as not to blow out the small piece of wood left on the leg or rail.

If you lay out your mortises that way you could do it and save a set up, but that would usually leave a very small section of stock.
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.