Woodnet Forums
Dovetail layout with bevel gauge - Printable Version

+- Woodnet Forums (https://forums.woodnet.net)
+-- Thread: Dovetail layout with bevel gauge (/showthread.php?tid=6841316)



Dovetail layout with bevel gauge - nodima - 09-28-2014

Struggling with marking dovetails using either of my bevel gauges, as the wing nut seems to always be in the way. Am I doing something wrong, or are the gauges only functional one way, and two are really required to layout both sides of the tails?

One is an "antique", the other is the small one Lee Valley sells. Same issue with both of them.


Re: Dovetail layout with bevel gauge - Sandal Woods - 09-28-2014

Not about the bevel gauges...

My suggestion on laying out the tails: Don't.

Instead, I always recommend a little practice using scraps, to learn to cut parallel to a line, or to two lines or more:



1. Number your practice cuts.
2. This will give you some idea how your dovetail saw is doing, and whether you must do a little tuning first.

For very small boxes (smaller than a dovetail jig will handle easily), I sometimes use a shop-made dovetail marker, with slopes more severe than is "normal":



Al

But much of the time I simply eyeball the angles. Try it, after practicing following parallel to a line.

Also, I suggest you keep your practice joints:




Re: Dovetail layout with bevel gauge - Derek Cohen - 09-28-2014

nodima said:


Struggling with marking dovetails using either of my bevel gauges, as the wing nut seems to always be in the way. Am I doing something wrong, or are the gauges only functional one way, and two are really required to layout both sides of the tails?

One is an "antique", the other is the small one Lee Valley sells. Same issue with both of them.




The only sliding bevel gauge that will not lose a setting is the model made by Chris Vesper. However that is overkill for dovetails. Get or make a dedicated dovetail marking gauge. There are so many designs that your head will swim. Whatever works for you.

Here are some I made from angle brass ...



Regards from Perth

Derek


Re: Dovetail layout with bevel gauge - dlgWoodWork - 09-28-2014

I don't use a bevel guage to mark mine. I made my own dovetail markers. There are several ways to make your own. Here's how I made mine.


Re: Dovetail layout with bevel gauge - Derek Cohen - 09-28-2014

dlgWoodWork said:


I don't use a bevel guage to mark mine. I made my own dovetail markers. There are several ways to make your own. Here's how I made mine.




I cannot recommend your construction. The wood grain runs in the wrong direction, and this makes them vulnerable to breaking.

Either make yours like Sandalwoods, or dovetail two pieces together so that the grain runs appropriately ...



Regards from Perth

Derek


Re: Dovetail layout with bevel gauge - hbmcc - 09-28-2014

nodima said:


Struggling with marking dovetails using either of my bevel gauges, as the wing nut seems to always be in the way. Am I doing something wrong, or are the gauges only functional one way, and two are really required to layout both sides of the tails?

One is an "antique", the other is the small one Lee Valley sells. Same issue with both of them.




you can unscrew and reset the bold for the older bevel. I have one that was also filed down to not protrude past the wood base. I am thinking Veritas can be fixed the same way. I was not aware that Veritas had the half flakey lever lock too.

Or, you can buy, or make, everything that the Handy Boys have. An adjustable bevel works fine, once it does what it should.

They're like glue clamps... Horny little things that proliferate like rabbits, or mice.


Re: Dovetail layout with bevel gauge - Rob Young - 09-28-2014

nodima said:


Struggling with marking dovetails using either of my bevel gauges, as the wing nut seems to always be in the way. Am I doing something wrong, or are the gauges only functional one way, and two are really required to layout both sides of the tails?

One is an "antique", the other is the small one Lee Valley sells. Same issue with both of them.




Get a bevel gauge with a cone washer lock such a s this

http://www.amazon.com/Sliding-T-Bevel-8-...ds=shinwa+bevel

Shinwa makes a smaller one but I didn't immediately find it on Amazon. Vintage ones exist and makers like Chris Vesper have a design that works great too. Vintage Stanley bevel gauges with the lever lock can be adjusted so the lock lever lines up with the frame and out of the way.

Or make a gauge or buy a gauge.


Re: Dovetail layout with bevel gauge - nodima - 09-29-2014

Thanks - great suggestions, I'll probably make up a couple of the guides and work from there.

Cheers.


Re: Dovetail layout with bevel gauge - GeorgeV - 09-29-2014

Paul Sellers has an easy to make dovetail marking gauge on You Tube video.

Easy and quick to make.

I use a 1:7 for just about everything. A nice compromise between 1:6 and 1:8


Re: Dovetail layout with bevel gauge - Bill_Houghton - 09-29-2014

Derek Cohen said:

The only sliding bevel gauge that will not lose a setting is the model made by Chris Vesper. However that is overkill for dovetails.



I have several Stanley 18s (and a Craftsman version of the same design) that hold their settings quite well in carpentry work, where they get banged around some; and a couple of the older Stanley bevels with the lever lock that also hold. I've never seen, much less used, the Vesper bevel, but it's hard to imagine it could be better.

Most bevels seem kinda large for dovetail marking, though.