Entry hall table for a niece: Part 8

Entry hall table for a niece: Part 8 - Printable Version

+- Woodnet Forums (https://www.forums.woodnet.net)
+-- Thread: Entry hall table for a niece: Part 8 (/showthread.php?tid=7352983)

Entry hall table for a niece: Part 8 - Derek Cohen - 02-17-2020

Following hot on the heels of the last post, where we created the male or tail section of the tapered sliding dovetail, now comes the female or pin socket to house the base for the legs.

[Image: 1a.jpg]

These are the bases. This post will focus on the socket for the one closest the camera.

[Image: 2a.jpg]

The base is positioned exactly 3 1/4" from the side. The tapered side is on the inside, with the outside face square to the front and rear of the case ...

[Image: 3a.jpg]

This process is essentially the same as transferring marks from the tail- to the pin board with drawers.

The base tapers towards the toe, that is, the sliding dovetail will tighten up as the base is pushed into the socket.

The first step is to register the far end of the base in such a way that the position is repeatable. This is done by placing a long board along the "square" side. The position for the end of the board is marked ...

[Image: 4a.jpg]

Now the base can be stood up to mark inside the tail with a scratch awl. You can make out the mark aligning the baseline of the tail ...

[Image: 5a.jpg]

Look carefully for the dots.

[Image: 6a.jpg]

This is repeated at the other end.

[Image: 7a.jpg]

The dots are now joined up ...

[Image: 8a.jpg]

The plan is to saw the socket sides, as if sawing dovetails in a drawer. The angle ratio is 1:6, as it was with the base. Since the socket is blind or stopped, the saw needs to have space in which to begin the cut. An area at the toe is excavated with a router.

The depth of the cut is set using a 7.0mm drill bit. I am aware that the actual depth is 7.5mm, but this will be a second pass. I intend to clear the waste with the router - this Jarrah is bloody hard, and I am not a masochist!
Smile

Using an angled saw guide, the end is chopped to the line ..

[Image: 11a.jpg]

Now this is space to register the azebiki saw ...

[Image: 12a.jpg]

I have roughly marked a depth to aim for ...

[Image: 13a.jpg]

RE: Entry hall table for a niece: Part 8 - Derek Cohen - 02-17-2020

Both sides have been sawn ...

[Image: 14a.jpg]

The waste is removed with the router, leaving a few mm close to the sides ...

[Image: 15a.jpg]

This is chopped away with a chisel in two passes, and then cleaned up with a hand router ...

[Image: 16a.jpg]

The side rebate #79/dovetail plane is used to clean any rough sections ..

[Image: 17a.jpg]

The power router drops a 0.5mm to 7.5mm and this is cleaned up ...

[Image: 18a.jpg]

Amazingly, the base slides in and tightens up about 1/4" from the end. It will need a tap to be fully secure.

[Image: 19a.jpg]

That's it for now.

Regards from Perth

Derek

RE: Entry hall table for a niece: Part 8 - hbmcc - 02-17-2020

Hi, Derek.
Setting up sliding dovetails has to be fiddly, and hair-raising to the last tap. Nice demo!!

Question: Are those rare earth magnets in the saw guide?

Thanks,
Bruce

RE: Entry hall table for a niece: Part 8 - Aram - 02-17-2020

Very nice done, Derek. That looks challenging.

RE: Entry hall table for a niece: Part 8 - gov.cheese - 02-17-2020

Enjoying your build as always, Derek. Did you have formal training or are you self-taught (or, some hybrid)?

RE: Entry hall table for a niece: Part 8 - Derek Cohen - 02-17-2020

(02-17-2020, 12:11 PM)hbmcc Wrote: Hi, Derek.
Setting up sliding dovetails has to be fiddly, and hair-raising to the last tap. Nice demo!!

Question: Are those rare earth magnets in the saw guide?

Thanks,
Bruce

Bruce, yes to rare earth magnets. They are under the surface. They are, of course, to hold a saw blade against the side.

One side of the straight edge is angled 1.6, and the other side is square.

Regards from Perth

Derek

RE: Entry hall table for a niece: Part 8 - Derek Cohen - 02-17-2020

(02-17-2020, 05:38 PM)gov.cheese Wrote: Enjoying your build as always, Derek. Did you have formal training or are you self-taught (or, some hybrid)?

No to formal training (but there are a lot of magazines, books and forums around ... although not so much when I started out quite a while back now). The mistakes are all my own responsibility and invention
Smile

Regards from Perth

Derel