+- Woodnet Forums (https://www.forums.woodnet.net)
+-- Thread: Formica corners problems (/showthread.php?tid=7356872)
Pages:
1
2
RE: Formica corners problems - Snipe Hunter - 07-28-2020
(07-28-2020, 09:32 AM)Admiral Wrote: I'm fairly certain that the substrates they use nowadays would not last as long....
They're using particle board these days. I've done a few with it and it's fine. Flatter than plywood. But you need a couple coats of contact cement on the board. The 1st coat has to dry before the 2nd coat.
RE: Formica corners problems - Cooler - 07-28-2020
(07-28-2020, 10:52 AM)Snipe Hunter Wrote: They're using particle board these days. I've done a few with it and it's fine. Flatter than plywood. But you need a couple coats of contact cement on the board. The 1st coat has to dry before the 2nd coat.
You also have to protect the underside from water. My kitchen counter had no such protection and over the dishwasher the particle board is crumbling.
At a minimum, I would seal it with some poly. I do worry about the heat though.
Aluminum roofing tape might work, but the adhesive might not hold up well to the heat of the dishwasher.
I think I would staple on some regular aluminum flashing extending about 1 foot on each side of the dishwasher.
RE: Formica corners problems - Roly - 07-28-2020
(07-28-2020, 11:37 AM)Cooler Wrote: You also have to protect the underside from water. My kitchen counter had no such protection and over the dishwasher the particle board is crumbling.
At a minimum, I would seal it with some poly. I do worry about the heat though.
Aluminum roofing tape might work, but the adhesive might not hold up well to the heat of the dishwasher.
I think I would staple on some regular aluminum flashing extending about 1 foot on each side of the dishwasher.
I put Formica on the underside of the countertop in the dishwasher area for that reason. The original countertop had the same issue as yours. Roly
RE: Formica corners problems - fixtureman - 07-28-2020
(07-28-2020, 11:37 AM)Cooler Wrote: You also have to protect the underside from water. My kitchen counter had no such protection and over the dishwasher the particle board is crumbling.
At a minimum, I would seal it with some poly. I do worry about the heat though.
Aluminum roofing tape might work, but the adhesive might not hold up well to the heat of the dishwasher.
I think I would staple on some regular aluminum flashing extending about 1 foot on each side of the dishwasher.
That is what backer lam is for
RE: Formica corners problems - Stwood_ - 07-28-2020
Back to the corners....
If there is enough overhang, miter them. Get some scraps from the cabinet shop and glue them on.
Get a laminate file to dress the edges down.
RE: Formica corners problems - barnowl - 07-28-2020
Formica countertops are relatively inexpensive.
I suggest you replace the entire thing, and incorporate a round edging.
Yes.....do it up right so you're both happy.... and you only cry once.
https://www.google.com/search?q=rounded+formica&source=lnms&tbm=isch&sa=X&ved=2ahUKEwjhtMbHxPDqAhXMknIEHQdrDyoQ_AUoAnoECA4QBA&biw=1399&bih=727#imgrc=mwIm6LI0xwbJ2M
RE: Formica corners problems - Cooler - 07-28-2020
(07-28-2020, 01:10 PM)barnowl Wrote: Formica countertops are relatively inexpensive.
I suggest you replace the entire thing, and incorporate a round edging.
Yes.....do it up right so you're both happy.... and you only cry once.
https://www.google.com/search?q=rounded+formica&source=lnms&tbm=isch&sa=X&ved=2ahUKEwjhtMbHxPDqAhXMknIEHQdrDyoQ_AUoAnoECA4QBA&biw=1399&bih=727#imgrc=mwIm6LI0xwbJ2M
That is not how I saw the issue. I suggested this approach (see below) which I used on my butcher block. Indeed if butcher block would look good adjacent to the formica, I would be inclined to put that in. It makes a good work surface, and it warms up a kitchen. I don't use mine as a work surface (I have cutting boards), so I put on three costs of oil based poly and waited two weeks before really using the surface.
![[Image: IMG_4536-495x400.jpg]](https://nesaw.com/wp-content/uploads/2018/07/IMG_4536-495x400.jpg)
This guy modified his peninsula at a claimed $400.00 total. A lot of bendy board.
https://www.domino.com/content/kitchen-peninsula-renovation/
RE: Formica corners problems - Mr_Mike - 07-28-2020
(07-27-2020, 07:18 PM)Robert Adams Wrote: Why should the contractor fix something they didn't do wrong. She didn't want to pay the extra for the curved so they made them square.
As for formica corners I don't like curves as they cone off eventually. Miters are the way to go but adding them after the fact... Not easy and not long lasting due to what you have to do to do it.
Not the shape, the fact they peel. But I now see the corners have not yet failed.