Finish advice for live edge walnut dining table - Printable Version +- Woodnet Forums (https://forums.woodnet.net) +-- Thread: Finish advice for live edge walnut dining table (/showthread.php?tid=7360720) |
Finish advice for live edge walnut dining table - measurecutcurse - 02-05-2021 I'm building a live edge dining table using air dried walnut slabs for the top, and cherry for the legs. I'm looking for a matte finish, preferably wipe on, that will provide durability for use as a dining table. It will get mostly occasional use, nit every day, but I want it to be moisture resistant for things like spills. All advice is welcome. Thanks RE: Finish advice for live edge walnut dining table - jteneyck - 02-05-2021 Any wiping varnish should meet your needs. I like Arm-R-Seal satin but you could use Waterlox OSF for a darker hue and rub it out after it's cured for a month. John RE: Finish advice for live edge walnut dining table - zaret - 02-09-2021 (02-05-2021, 01:12 PM)jteneyck Wrote: Any wiping varnish should meet your needs. I like Arm-R-Seal satin but you could use Waterlox OSF for a darker hue and rub it out after it's cured for a month. this. john nailed it. ARM on walnut is my go-to, but waterlox is also beautiful. one's a urethane resin, one's an alkyd resin. the waterlox is deeper color, more orange. on my walnut pieces in my house, i use arm-r-seal over seal-a-cell. good luck, post pictures when you're done! sounds like one heck of a piece. RE: Finish advice for live edge walnut dining table - jteneyck - 02-10-2021 (02-09-2021, 08:00 PM)zaret Wrote: this. john nailed it. ARM on walnut is my go-to, but waterlox is also beautiful. one's a urethane resin, one's an alkyd resin. the waterlox is deeper color, more orange. on my walnut pieces in my house, i use arm-r-seal over seal-a-cell. Not that it matters much, but Waterlox uses a phenolic resin. P&L 38 (I think that's the name) uses an alkyd resin. And you are right that Waterlox gives a deeper color. Arm-R-Seal is actually pretty clear for an oil based varnish. I've used it on curly maple and it imparts very little amber hue. John RE: Finish advice for live edge walnut dining table - rwe2156 - 02-10-2021 I hope that baby stays flat!! Are you installing any metal braces? RE: Finish advice for live edge walnut dining table - zaret - 02-10-2021 (02-10-2021, 10:20 AM)jteneyck Wrote: Not that it matters much, but Waterlox uses a phenolic resin. P&L 38 (I think that's the name) uses an alkyd resin. And you are right that Waterlox gives a deeper color. Arm-R-Seal is actually pretty clear for an oil based varnish. I've used it on curly maple and it imparts very little amber hue. John - thanks for this, of course, you are correct. arm-r-seal is wonderful stuff... in fact, i used some just this morning on three walnut mantles. by the way - my go-to now for hard maple is odie's oil. i'm yet to find a more beautiful finish on maple. pretty on walnut, too. and, zero VOCs, which is nice. RE: Finish advice for live edge walnut dining table - measurecutcurse - 02-10-2021 (02-10-2021, 10:36 AM)rwe2156 Wrote: I hope that baby stays flat!! No. That woods been in the shop for ~3 years and off the mill for at least 6. It hasn't moved, and it is made op of 4 different boards, and the grain direction alternates. None of my live edge pieces have moved at all. RE: Finish advice for live edge walnut dining table - jteneyck - 02-11-2021 (02-10-2021, 01:50 PM)zaret Wrote: John - thanks for this, of course, you are correct. arm-r-seal is wonderful stuff... in fact, i used some just this morning on three walnut mantles. Thanks. I've wanted to try Odie's Oil. Might just have to now. John |