Search Results
|
Post |
Author |
Forum |
Replies |
Views |
Posted
[asc]
|
|
|
Thread: Craftsman Jointer Knife Removal
Post: RE: Craftsman Jointer Knife Removal
To wrap this up - I got the other two blades out. I'll stone the wedges and the back of the knives to mage sure nothing got mangled in the beating process.
Thanks again. |
|
bjordan |
Woodworking Power Tools
|
7 |
1,449 |
12-29-2022, 03:10 PM |
|
|
Thread: Craftsman Jointer Knife Removal
Post: RE: Craftsman Jointer Knife Removal
Success!!
I got the wedge out this morning that I was working on yesterday. I had to use a 2 pound brass hammer and a 1/4" steel drift. But, nothing was damaged and that sucker was STUCK. Now, o... |
|
bjordan |
Woodworking Power Tools
|
7 |
1,449 |
12-28-2022, 12:32 PM |
|
|
Thread: Craftsman Jointer Knife Removal
Post: RE: Craftsman Jointer Knife Removal
KC Wrote: (12-28-2022, 06:51 AM)
--
Take special notice of where your hands are. Closest I ever came to losing a finger was changing jointer knives. Wrench slipped off...
--
Excellent advice! I ... |
|
bjordan |
Woodworking Power Tools
|
7 |
1,449 |
12-28-2022, 10:02 AM |
|
|
Thread: Craftsman Jointer Knife Removal
Post: RE: Craftsman Jointer Knife Removal
jteneyck Wrote: (12-27-2022, 11:46 AM)
--
The knife and/or wedge must be rusted in place. Lots of PB blaster for a day or two. Then fashion a block of 3/4" hardwood maybe 2" wide and a few inches l... |
|
bjordan |
Woodworking Power Tools
|
7 |
1,449 |
12-27-2022, 01:04 PM |
|
|
Thread: Craftsman Jointer Knife Removal
Post: Craftsman Jointer Knife Removal
Hi Folks,
Forgive me if this has been covered before. I am finally going to sharpen my old Craftsman 4" jointer knives. This jointer is probably from the early 1990s and was given to me by a good... |
|
bjordan |
Woodworking Power Tools
|
7 |
1,449 |
12-27-2022, 11:18 AM |
|
|
Thread: Mail Order Lumber Supplier
Post: RE: Mail Order Lumber Supplier
Thanks everyone for the suggestions! |
|
bjordan |
Woodworking
|
7 |
1,322 |
11-27-2022, 11:18 AM |
|
|
Thread: Mail Order Lumber Supplier
Post: Mail Order Lumber Supplier
Hi Folks.
Years ago, I used to get cherry lumber shipped in due to not having a supplier near me. I am now in a different location and once again, no hardwood suppliers near me.
Is there a ... |
|
bjordan |
Woodworking
|
7 |
1,322 |
11-26-2022, 12:48 PM |
|
|
Thread: Router for Craftsman 171.25484 Table?
Post: RE: Router for Craftsman 171.25484 Table?
fredhargis Wrote: (12-17-2021, 12:28 PM)
--
I suspect the problem you are facing is one common to Craftsman tools, a majority of their accessories were made uniquely to fit only the Craftsman line of... |
|
bjordan |
Woodworking Power Tools
|
3 |
1,880 |
12-18-2021, 11:07 AM |
|
|
Thread: Router for Craftsman 171.25484 Table?
Post: Router for Craftsman 171.25484 Table?
Hello. I have an older Craftsman 171.25484 router table and I am trying tying to mate a router to it. Per the manual, these Craftsman routers will bolt to it: 9-27504, 9-27505, 9-27506, 9-27510 and... |
|
bjordan |
Woodworking Power Tools
|
3 |
1,880 |
12-17-2021, 10:54 AM |