Search Results
|
Post |
Author |
Forum |
Replies |
Views |
Posted
[asc]
|
|
|
Thread: Milling Handrail
Post: RE: Milling Handrail
Stwood_ Wrote: (12-16-2019, 06:31 PM)
--
Well.........we're not neighbors. :)
If you make it to Missouri....
--
Oh well, thanks for the offer. I used to travel through there when I lived in Ne... |
|
gtrgeo |
Woodworking
|
26 |
13,319 |
12-16-2019, 07:01 PM |
|
|
Thread: Milling Handrail
Post: RE: Milling Handrail
jteneyck Wrote: (12-16-2019, 05:20 PM)
--
George, not looking for an argument either. This is the part of your design I'm not sure about:
This required depth shall continue
for at least 3/8 i... |
|
gtrgeo |
Woodworking
|
26 |
13,319 |
12-16-2019, 06:55 PM |
|
|
Thread: Milling Handrail
Post: RE: Milling Handrail
Stwood_ Wrote: (12-16-2019, 04:07 PM)
--
Sure. :laugh: Where are you?
--
I am just outside of Portland Oregon. |
|
gtrgeo |
Woodworking
|
26 |
13,319 |
12-16-2019, 06:24 PM |
|
|
Thread: Milling Handrail
Post: RE: Milling Handrail
Turner52 - I appreciate you bringing up the code aspect as I would hate to have to rework down the road when we sell.
Stwood - Want to be my buddy with a molder/planer? :D
I am still debating ... |
|
gtrgeo |
Woodworking
|
26 |
13,319 |
12-16-2019, 03:37 PM |
|
|
Thread: Milling Handrail
Post: RE: Milling Handrail
John,
I found the same code language when I was putting that design together. Unless I am reading the code wrong, I believe it meets the criteria. The taper starts at 3/4" below the peak and meets t... |
|
gtrgeo |
Woodworking
|
26 |
13,319 |
12-16-2019, 12:07 AM |
|
|
Thread: Milling Handrail
Post: RE: Milling Handrail
Looking around some more I found this bit from Magnate. It has the straight lines I am looking for. https://www.magnate.net/ProductDetails.asp?ProductCode=4901
I believe I can cut the chamfers on t... |
|
gtrgeo |
Woodworking
|
26 |
13,319 |
12-14-2019, 12:16 PM |
|
|
Thread: Milling Handrail
Post: RE: Milling Handrail
Thanks for the suggestion Mike. I am looking for something with a little more square features than the windo sill cutter would provide. Looking at those cutters they seem to be limited to ~1-1/8" cutt... |
|
gtrgeo |
Woodworking
|
26 |
13,319 |
12-14-2019, 11:37 AM |
|
|
Thread: Milling Handrail
Post: RE: Milling Handrail
John,
You do some beautiful work. Thanks again for the help. I hope my project turns out half as nice as yours the rails and steps will be stained oak with everything else painted white to match the... |
|
gtrgeo |
Woodworking
|
26 |
13,319 |
12-13-2019, 11:42 PM |
|
|
Thread: Milling Handrail
Post: RE: Milling Handrail
jteneyck Wrote: (12-13-2019, 10:20 AM)
--
I have milled handrails very similar to what you want to do, and of about the same dimensions. And the comment about adhering to building codes is spot on. ... |
|
gtrgeo |
Woodworking
|
26 |
13,319 |
12-13-2019, 01:27 PM |
|
|
Thread: Milling Handrail
Post: RE: Milling Handrail
Turner52 Wrote: (12-12-2019, 03:23 PM)
--
Check the building codes in your area. They have been changed in most areas to greatly reduce the allowable width. Easier to hang onto thatway. Probably the ... |
|
gtrgeo |
Woodworking
|
26 |
13,319 |
12-12-2019, 03:40 PM |
|
|
Thread: Milling Handrail
Post: Milling Handrail
I am planning some remodel on the stairs in my home and have bottomed out on everything except the handrail. I am having a hard time finding a ready made handrail that matches what I have envisioned f... |
|
gtrgeo |
Woodworking
|
26 |
13,319 |
12-12-2019, 01:18 PM |