Posts: 3,193
Threads: 0
Joined: Jul 2005
I've got a bunch of old-fashioned door handles that use small, conical set screws. I need a bunch of replacements, but can' find anywhere that sells them.
The large set screw in the photo is a 1/4" from Amazon -- It's a tad too big, and wont thread through the hole at all.
Any suggestions?
Thanks in advance.
Posts: 1,881
Threads: 0
Joined: Feb 2008
Just thinking. I'd start with the right dia. and thread pitch in brass. That should be easy to find in a machine screw. Then I'd need a hacksaw blade, a file, pliers (or vice grip), a drill to make it easier, and about 1 minute for each one. Now I could also consider cheating a little by using a long machine screw to lock one knob onto the shaft and cutting it off flush, then with the remaining, make a set screw or just cut it so it doesn't stick out too far for the other knob.
Sign at N.E. Vocational School Cabinetmaking Shop 1976, "Free knowledge given daily... Bring your own container"
Posts: 2,044
Threads: 1
Joined: Feb 2009
Location: Mechanicsville, Md
I just did a quick search on McMaster Carr using 1/4" as the length. Found a few options. You can change the search options for more results. I'm not sure that these are what you are looking for but maybe.
https://www.mcmaster.com/screws/set-scre...-screws-7/
I no longer build museums but don't want to change my name. My new job is a lot less stressful. Life is much better.
Garry
Posts: 63,560
Threads: 3
Joined: Feb 2007
Location: Merryland
Just make some. Grind a threaded rod to a point. Cut to length and cut sth slit. Or. Just uce a allen set screw and grind the tip to a poit.
Posts: 3,193
Threads: 0
Joined: Jul 2005
08-15-2022, 07:06 AM
(This post was last modified: 08-15-2022, 10:52 AM by David Stone.)
That’s a lot more work than I was hoping for.
Posts: 17,269
Threads: 2
Joined: Sep 2002
Location: pburg, wv
08-18-2022, 03:16 PM
(This post was last modified: 08-18-2022, 04:06 PM by oscarMadison.)
you might try here.
Is the problem the thread size or length? One of the places sells brass set screws that are 10-24.
https://www.historichouseparts.com/?targ...luding=all
or here
https://www.houseofantiquehardware.com/
So do the doors that go with that have a mortise lock?
I don't know if that site has it but you can buy replacement spindles that have holes through the then length wouldn't be an issue.
Is the problem the thread size or length? One of the places above sells brass set screws that are 10-24.
mark
Ignorance is bliss -- I'm very, very happy
Posts: 22,518
Threads: 0
Joined: Feb 2005
Location: Regina Saskatchewan Canada
First, you don’t need that sharp a point. Second, I wouldn’t mess with brass screws, point the holes to the bottom and use standard steel set screws. Third, buy a 1/4 - 20 tap and run it into the existing holes so a common screw will fit. Done.
Blackhat
Bad experiences come from poor decisions. So do good stories.
Posts: 39,571
Threads: 0
Joined: Apr 2007
(08-19-2022, 02:06 PM)blackhat Wrote: First, you don’t need that sharp a point. Second, I wouldn’t mess with brass screws, point the holes to the bottom and use standard steel set screws. Third, buy a 1/4 - 20 tap and run it into the existing holes so a common screw will fit. Done.
Funny this popped up today as I just had to swap out an old glass handled knob in my kids room. I have a large supply but most are clear and the knob I replaced has a bit of purple in the glass and the plan is to eventually tap it to the next size up and a new set screw. Today was all about making it so they could get out of the room.
Phydeaux said "Loving your enemy and doing good for those that hurt you does not preclude killing them if they make that necessary."
Phil Thien
women have trouble understanding Trump's MAGA theme because they had so little involvement in making America great the first time around.