#13
Using a hook knife....

https://www.youtube.com/watch?v=jpnx9kuZeqg

And another

https://www.youtube.com/watch?v=6rZK3WLTse4
Often Tested.    Always Faithful.      Brothers Forever

Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Upset





Reply

#14
Thanks
Reply
#15
The first one is interesting in that he mostly uses what is essentially a hunting knife for most of the process. Not traditional, but it seems to work pretty well. More control with that knife than I would have thought.
Still Learning,

Allan Hill
Reply

#16
Same here... Properly sharpened hook knives are my tool of choice for hollowing spoon bowls.
Often Tested.    Always Faithful.      Brothers Forever

Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Upset





Reply

#17
Jack

How does a person make a hook in a knife?

Then how is it sharpened?

Arlin
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Reply

#18
Arlin, The way I do it is, I do a rough sharpening job on a piece of steel I want to become the blade...Then I heat the steel bright red {in daylight} and bend it about half way around a piece of pipe that I have clamped in my bench vise..The pipe is the diameter that I want for the hook...Then, while it is still cherry red, I quench it slowly in oil {or water, depending on the type of steel}.....I prefer the bevel to be on the outside of the blade, but I have made them with the bevel on the inside...and I have made some with a double bevel...after the steel has cooled, I "brighten" the steel with an abrasive like sandpaper, removing the oxide that forms..At that point, I temper it...I usually do that with a slow flame from the torch...I "play" the flame over the steel uniformly until the color change reaches a light "straw" yellow color.{ if one has never done it that way, an oven at ~400* will work}..At that point, the steel is tempered so that it has the best edge-holding ability, without becoming overly "brittle"..Of course, there again, it depends on the type of steel, but that's what I do when I am using O1 tool steel. From there, I do the final honing for a razor edge, and for that, I usually use my Dremel with a Cratex wheel for the inside bevel, and a fine belt on a grinder, finishing up with a leather polishing strop, for the outside..You can also sharpen the hook using the appropriate hones an/or leather wheels. . {And you can make very small LEATHER wheels for stropping the inside bevel with your Dremel.}..I can't remember ever NOT having a Dremel..I don't know how anyone does without one...
Often Tested.    Always Faithful.      Brothers Forever

Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Upset





Reply

#19
Jack

I did not know if you used a torch or forge or the thickness of the metal you used it to bend with.

I did email Gene Henrikson who makes small forges (http://walnutforge.com/Gallery.php) and he makes some really really good ones at a less then $200

Arlin
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Reply
#20
Hook Knives can also be purchased:

http://www.amazon.com/Morakniv-Carving-K...B00343VCCK

http://www.highlandwoodworking.com/frost...knife.aspx

http://www.highlandwoodworking.com/flexc...-kn26.aspx

Pinewood forge also makes very, very good hook knives, but they are more pricey and you may need to wait until he makes a batch. Hook knives come in right handed, left handed, and dual handed versions.
Still Learning,

Allan Hill
Reply

#21
Allan

If you remember Del Stubbs the turner that is what he makes now.

http://pinewoodforge.com/

Arlin
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Reply

#22
Arlin Eastman said:


Allan

If you remember Del Stubbs the turner that is what he makes now.

http://pinewoodforge.com/

Arlin




My hook knife is a Pinewood Forge. Just offering more affordable alternatives for the rest of the crowd out there. Not sure I'd spend $200 on a hook knife, though. I can't imagine it would be 4-7x better than some of those I linked to.
Still Learning,

Allan Hill
Reply
Spoon carving video


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.