#22
Most of the haul for the other weekend was cherry ( I thought..)
[attachment=2915]
I grabbed the one 6/4 slab..hauled it to the shop to make four leg blanks..
.[attachment=2916]
Bandsaw tried to follow the grain a bit....
[attachment=2917]
"We have ways"   Jointed the sawn edges smooth, got rid of the saw marks
[attachment=2918]
Worn out, soaked clean through....took a break for a while.....
Show me a picture, I'll build a project from that
Reply

#23
Ok, break's over.   Selected a rather plain-looking 4/4 x 6 and went to the shop. 

Needed a few aprons, and what was left would make a couple stretchers.    Again, bandsaw to rip to width....then a mitre saw to cross cut the smaller pieces.
[attachment=2919]
And got out some smaller planes to remove the saw marks..
[attachment=2920]
But, there was a "problem" with this plain looking wood....when I planed away the saw marks..
Uhoh
[attachment=2921]
What I thought was just planer marks..
No
[attachment=2922]
Turned out to be a bit of Tiger stripe Cherry?
Confused   Curly Maple?
Confused
[attachment=2923]
I think I will have about....three fingers worth and call it a day..

( Underhill's Rachel's Standing Desk)   Hoping to make mine in Cherry, instead of pine....
Wink
Show me a picture, I'll build a project from that
Reply
#24
Oops....
Raised
Reply
#25
So I see that crafty seller slipped in some wonky grained stock.
===---===---===---===---===---===---===---===---
Please visit my website
splintermaking.com
Reply
#26
Yep, it looks like everything you got there is maple and curly maple. It is pretty easily identifiable by looking at the edges of the boards.
Reply
#27
(06-28-2017, 06:27 AM)JimReed@Tallahassee Wrote: So I see that crafty seller slipped in some wonky grained stock.

Are you talking about the 'sour grain' ?  
Smile
Chris
Reply
#28
I can't complain too much....since the stuff was FREE
Winkgrin 

1/2 of a pickup truck load, the other 1/2 went to the driver.   Fellow was merely cleaning out his off-cut piles.  
Cool  

Will dig through the stack when I get  some better lighting today, and see how many more such scrap boards are in that pile I brought home
Yes
Show me a picture, I'll build a project from that
Reply
#29
Well, needed to cut the front and back aprons to a better length, so..
[attachment=2930]
26" long, counting tenons...
[attachment=2931]
Yeah, these things....1/4" thick, for a 3/4" deep mortise.

Details, details.
[attachment=2932]
Stretcher that sits near the bottom of the legs.   All four corners got a bead.  The aprons?
[attachment=2933]
Only get one bead.   A smooth plane to do a bit of clean up.

After Lunch, there MAY be some chopping done..
[attachment=2934]
Stay tuned...
Show me a picture, I'll build a project from that
Reply
#30
  • Leg work today[attachment=2936]
Show me a picture, I'll build a project from that
Reply
#31
Ok, that was ...special..
Confused 
Chisels were to chop a few mortises
[attachment=2937]
Had aprons that needed a few.  Once the top of a leg was done, I drug out the Stanley 45, had details to do
[attachment=2938]
Used the same #23 bead cutter.   just went down two faces to a corner bead. 
Stretcher needed a smaller mortise..
[attachment=2939]
And fitted
[attachment=2940]
Not sure why I did a big dry fit..
[attachment=2941]
Other than to see how much trouble this will be to glue and clamp up...might be a bit ugly to do all at one shot
Uhoh
Rolleyes
Maybe do a few sub-assemblies
Confused like each end first?  Less hassle
Confused ?

Have the front legs done, need to get the back legs done tomorrow.   Maybe a glue up, or two later?  

Stay tuned.
Show me a picture, I'll build a project from that
Reply
Next Project


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.