Posts: 4,751
Threads: 0
Joined: Aug 2006
Got an extra set of knives with the Parks planer, I just bought.
They are hollow ground, with no micro bevel.
Should there be a micro bevel? And if so what angle, and how wide should it be?
Thanks for any info
I long for the days when Coke was a soft drink, and Black and Decker was a quality tool.
Happiness is a snipe free planer
Posts: 10,630
Threads: 0
Joined: Jul 2005
Location: Front seat on the Struggle Bus
When I used to run knifed planer heads, none ever had a micro bevel.......
Ed
Posts: 12,477
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
It's not something that's usually done, I'd skip it.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 13,391
Threads: 4
Joined: Jun 2007
Location: New Jersey
(09-26-2019, 06:05 PM)Pirate Wrote: Should there be a micro bevel?
I've never heard of this, seems like gilding a lilly to me, and it would likely not make much difference.
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Posts: 12,715
Threads: 0
Joined: Jan 2010
Location: Lewiston, NY
(09-26-2019, 06:05 PM)Pirate Wrote: Got an extra set of knives with the Parks planer, I just bought.
They are hollow ground, with no micro bevel.
Should there be a micro bevel? And if so what angle, and how wide should it be?
Thanks for any info
Whether or not you add a micro-bevel, the angle needs to be what the manufacturer specifies where the knife hits the wood. If the knife as it now is is at the correct angle adding a micro-bevel will cause the heal of the micro-bevel to compress the wood behind where the point is cutting. The resultant compression marks are darned hard to sand out.
John
Posts: 4,751
Threads: 0
Joined: Aug 2006
Parks manual doesn't mention knife angle.
I've read 40 - 50 degrees.
Problem is. The hollow ground edge measures 35 degrees, across the edge. But with the hollow grind, the actual angle at the edge must be 30 degrees or less.
I've heard with a hollow grind and micro bevel, it's easier to hone knives in place, because the edge is narrower, than a flat grind.
I long for the days when Coke was a soft drink, and Black and Decker was a quality tool.
Happiness is a snipe free planer
Posts: 4,751
Threads: 0
Joined: Aug 2006
Just checked knives in the machine. Had to use a 30x pocket microscope to see it! They have a micro bevel.
Now just need to find micro bevel angle.
I long for the days when Coke was a soft drink, and Black and Decker was a quality tool.
Happiness is a snipe free planer
Posts: 12,715
Threads: 0
Joined: Jan 2010
Location: Lewiston, NY
09-27-2019, 12:18 PM
(This post was last modified: 09-27-2019, 12:18 PM by jteneyck.)
(09-27-2019, 11:51 AM)Pirate Wrote: Parks manual doesn't mention knife angle.
I've read 40 - 50 degrees.
Problem is. The hollow ground edge measures 35 degrees, across the edge. But with the hollow grind, the actual angle at the edge must be 30 degrees or less.
I've heard with a hollow grind and micro bevel, it's easier to hone knives in place, because the edge is narrower, than a flat grind.
I think that's far too wide a range. I had a planer that required a 45 deg bevel, another at the same time that was 42 deg. I once forgot and sharpened both sets at 42 deg. The one that required 45 deg planed poorly and left those compression marks I described earlier.
If you go to OWWM.org someone can point you to the manual for that machine if you don't have one.
The problem with the micro bevel approach is once you hit a nail, staple, or piece of dirt you have to grind the knife back more than had it not had the micro bevel, so you will get less sharpenings out of a set of blades if you put a micro bevel on them each time. My observations showed no improvement in cut quality.
John
Posts: 4,751
Threads: 0
Joined: Aug 2006
Are you talking about a flat ground knife with and without a micro bevel, or the same with a hollow ground knife?
With the hollow grind, I don't think an edge with less than 30 degrees would last long.
The knives in the machine, hollow grind and micro bevel, are still very sharp.
I long for the days when Coke was a soft drink, and Black and Decker was a quality tool.
Happiness is a snipe free planer
Posts: 115,110
Threads: 0
Joined: Jun 2002
Location: Sparkling Clearwater, Fl. Tampa Bay Area
(09-26-2019, 06:05 PM)Pirate Wrote: Got an extra set of knives with the Parks planer, I just bought.
They are hollow ground, with no micro bevel.
Should there be a micro bevel? And if so what angle, and how wide should it be?
Thanks for any info ....................
A micro bevel has the effect of "blunting" the edge while making it stronger...Edges get more "blunt" are they are used...No point in starting out with a blunt edge..let nature take it's course...
Often Tested. Always Faithful. Brothers Forever
Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
|