Cherry Drop-Leaf Table
#11
We needed a table near the front door for keys, sunglasses, mail and other stuff that I'd rather not have collected on the kitchen counters (small pet peeve of mine). I was originally going to make an arts and crafts style table, but I never found a piece that I really was interested in building. Then I happened across this table in a popular woodworking book:



I showed the photo to my wife and explained the table could be used for other purposes with the extensions raised. She approved and since I had a lot of cherry laying around, I decided I'd be faithful to the article.

The legs splay out 4 degrees in both directions so a 5.5 degree cut across the diagonal gives the right flare. I didn't have a chopsaw, so a I used the same cradle idea from the article only attached to a sled:



Mortises were cut, then a simple taper leg jig, followed by aprons and finally a test fit.





For what its worth, I have no idea what the exact angle of the aprons are. After I made the 5.5 degree cut, I stood the leg up on end and used a bevel gauge to find the angle. I kept it set throughout the project.

The issue was cutting out the spinners for table supports. This was an issue. The article says you cut the top of the spinner to the same angle as the aprons, but the bottom of the spinner and the top of the cutout in the apron should be square. It didn't seem right to me, after all the apron is angled, so a 90 degree cut wouldn't be parallel with the top. But I had faith in popular ww'ings editors... which was a mistake. They attach their spinners with a screw. I thought it seemed really sloppy and not at all right.

I was trying to use the cutout as the spinner too (Norm does this in one of his builds), but I thought it made a bad problem worse. Whats more, I was convinced the spinner should be angled on the top and the bottom and the apron cutout should be angled too. So I sat and thought for a long time and decided the only way I could create that inside angle on the apron was with a tilted router.

Real classy, I know


This left just a little clean up on the ends:



I chose to make the spinners turn on 1/4" dowel which mean drilling straight down with the apron at the correct angle on the drill press. I used an apron end cut to the tilt the apron and drilled through the spinner and the apron at the same time. The finished spinner worked much better.





Now it was on the table top. I cut the drop leaf edge on the shaper running in reverse. I wanted both profiles to register off the bottom of the table and the profile I had, would only work in reverse.



The u-shaped block of wood is a hold down/guard. Very handy and works well. Here it is in operational position.


As you can see, no DC attached which wasn't the best decision.

With the hinges in hand and test parts but, I started fitting the hinges. Rule joints are a real pain in the butt. This was suppose to be a quick and easy build and, and .....

Anyway, I figured out how I wanted the hinges and where and then drew outlines. I didn't bother with a router template, I just free handed and cleaned it up with a chisel. A second router was used for the barrel.



Glued up the short ends first then all together.





Finished with a very thin coat of BLO and then arm-r-seal.





Reply
#12


Very nice!

Ed < loves Cherry.
Reply
#13
Awesome post Jonny. Sure looked like a simple table

It's those "simple" things that hold some of the biggest challenges. I like your work through s, and the finished product looks very nice. Nice work. When that Cherry gets it's suntan, that is really going to be nice. Love Cherry when it's new, love it more when it darkens.
Worst thing they can do is cook ya and eat ya

GW
Reply
#14
PURTY !!!!
Reply
#15
What is that tool in the background in pic #4 from the top?

Looks like an absolute monster, whatever it is.

Nice table, BTW.
Reply
#16
Herb G said:


What is that tool in the background in pic #4 from the top?

Looks like an absolute monster, whatever it is.

Nice table, BTW.




Thanks. The machine is an American 12" Jointer.
Reply
#17
Sweet. Impressive looking shop too.
Reply
#18
Your table is beautiful! Great work.

Legs that are raked and splayed as on this table create an interesting challenge, don't they? The corresponding faces on the legs are out of parallel in both the vertical and horizontal directions making it tricky to cut the shoulders for the the tenons on the ends of the aprons.
Reply
#19
DaveR1 said:


Your table is beautiful! Great work.

Legs that are raked and splayed as on this table create an interesting challenge, don't they? The corresponding faces on the legs are out of parallel in both the vertical and horizontal directions making it tricky to cut the shoulders for the the tenons on the ends of the aprons.




Yeah it wasn't terrible except for those leaf supports. The angles do seem to be everywhere though. Top and bottom of the aprons, the tenons, and then the groove for the table top clips.
Reply
#20
Garrett Hack has done several tables with raked and splayed legs. To make his even more of a challenge, the legs are tapered over their entire length so you can't easily use the outside faces of the legs for a reference for the insides as you might when cutting mortises. One of his designs has a drawer that spins out like your leaf supports. He rips the apron at the bevel angle, cuts out the drawer front and glues the pieces back together. I suppose you could do the same sort of thing for your table. It wouldn't be very noticeable up under the top. That is, if you build another one.

Another thing that isn't real obvious at first look is the pivot for the support needs to be vertical and not parallel to the face of the apron.
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.