Bandsaw Fence Recommendations?
#17
(03-06-2017, 08:51 PM)jcredding Wrote: I have an 18" Rikon bandsaw (model 10-345) and have always hated the fence that came with it.  Though I don't do a lot, I need something that would be appropriate for resawing only occasionally.  Would appreciate any thoughts on good options.

Thanks,
John

Not an 18" saw, but for my Grizz w/ 6" riser I just made an "L".  Stuff between 4" and 7" tall uses the short leg.  Taller stuff, flip it and use the tall leg.

I use the stock fence to set it square to the blade, then clamp down.  Shim for parallel cuts by adding a little blue tape before clamping down.

[Image: 31398327984_e81cc4e262_z.jpg]

[Image: 31429315303_0a39a38468_c.jpg]

You can just barely make out numbers on the boards in the second picture.  This was my initial test was making 1/16" (0.0625") cherry veneer.  Measured several points along length and found that I was at most off about 0.005" end-to-end on the boards (that would be the so-called "drift") and maybe a few thousand edge to edge (parallelism).  Not bad for scraps of MDF, blue tape and the cheap 1/2" blade from Grizzly.

Most of the time I'm resawing for 1/8" to 1/4" so that sort of error not worth chasing.
Don't sweat the petty things and don't pet the sweaty things. -- G. Carlin
Reply
#18
Could never understand why anyone would want to hand guide a piece of wood to resaw.
That's what the fence is for!
I put a 16" Jet fence (thanks Lumberyard) on my old Delta 14" and it works fine.
I long for the days when Coke was a soft drink, and Black and Decker was a quality tool.
Happiness is a snipe free planer
Reply
#19
(03-15-2017, 07:53 AM)Pirate Wrote: Could never understand why anyone would want to hand guide a piece of wood to resaw.
That's what the fence is for!
I put a 16" Jet fence (thanks Lumberyard) on my old Delta 14" and it works fine.

They do it because they can't get their saw to cut straight. 

John
Reply
#20
My saw works very well off the fence if I choose to set it up. I can scribe a line and have a "one of" cut cleanly off that big pin in less than it takes to find the fence. I make a lot of boxes, and for most I only need 1 resaw, for that it doesn't make sense for me to spend more time than I do.
Worst thing they can do is cook ya and eat ya

GW
Reply
#21
(03-15-2017, 06:39 PM)Steve N Wrote: My saw works very well off the fence if I choose to set it up. I can scribe a line and have a "one of" cut cleanly off that big pin in less than it takes to find the fence. I make a lot of boxes, and for most I only need 1 resaw, for that it doesn't make sense for me to spend more time than I do.

Even with my minimalist fence, it's sometimes easier to scribe and cut without a gauge, which is what the fence is, realistically.  I do have to use my hands, either way.
Better to follow the leader than the pack. Less to step in.
Reply
#22
Well I probably should have added that I keep the pin in most of the time, as it is used more than the fence, thus having to go find the fence when I want to resaw veneer slabs.
Worst thing they can do is cook ya and eat ya

GW
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.