Boss wants a Pantry Cupboard
#11
Well, I had just gone through and resawn a few reclaimed 2x4s down....Boss comes up and says she wants a new pantry cupboard.   had to go out and buy a bit of pine.   1x4s, 1x8s, and a couple 1 x 10s, all 6' long.

Glued up two panels to make the sides
   
And ripped a 1x4 to make the stiles for a face frame
Had to crosscut a second 1 x 4
   
Used the "new" panel saw for that.   Needed two rails at 30" long.  Join the rails to the stiles with half laps
   
Needed to rip a few more parts, to make two webframes to help join the sides together..
   
Had a benchful of tools to work on the laps..
   
Just the usual suspects....
Rolleyes

Stay tuned for the next episode....hope you like it.
Show me a picture, I'll build a project from that
Reply
#12
I'm waiting for a popcorn refill.
Winkgrin
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply
#13
(05-23-2017, 05:35 PM)Stwood_ Wrote: I'm waiting for a popcorn refill.
Winkgrin

Can I have carrots and broccoli? 
Crazy

There's wood. I have lots of that; and even for projects--some projects are forgotten. 

Waiting......

Mmmmmm .....

Hhhhhuuuummmmmm .. oh hum....
Reply
#14
Sure. Eat all your carrots.



Drumming fingers on desk.

Tap tap.....
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply
#15
Will just have to wait until tomorrow evening, for the next episode...

til then...
   
These USED to be a few 2 x 4s I salvaged.   Resawn down to 3/4 x 3"
   
The plain side..
   
Saw mark side,,,
   
Millers Falls #11 Junior Jack to smooth out both sides. 

Will use these for parts for the cupboard build. 

While you are waiting...
   
The "other" kind of Dew should keep things interesting....
Rolleyes




Show me a picture, I'll build a project from that
Reply
#16
Oooh ok...............waiting till evening........
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply
#17
Ok, this might take two posts....here goes ( until the glue dries...
Rolleyes)
Cleaned all the saw marks up, made a LOT of shavings...
   
The four shorter [ieces of the webframes needed tenons made
   
Needed to set up a jig to chop a few mortises..
   
Just three pieces of scrap.  I can clamp each part in place...
   
And do a mortise to match the tenon..
   
Something like this.   I chop into the far end, after a saw has made a kerf to follow.   Pop the waste out. 

Part 2...
Show me a picture, I'll build a project from that
Reply
#18
Part 2:  Dry fits..
   
Tenons seem to fit nicely, got all four corners done..
   
And check for square..
   
Looks decent.   Went ahead and made both frames.   Bottom webframe was glued up first..
   
Not enough space ....
Show me a picture, I'll build a project from that
Reply
#19
For the rest of this morning's efforts....so, page three...
Top frame was a little different..
   
Only one stiffener was used, as only the top is above it.  Doesn't need to support a lot of can goods. 

On both the sets of stiffeners,  pilot holes were drilled.   then a small drill was used
   
With a countersink bit...

The single one was centered,  the other two were set in about 5" from the outside edge.   Drove one screw ( glue was applied first) and check for square, then drive the other screws. 

So, Lunch Break!   I have both webframes sitting all clamped up, once the glue has set, I can work on gluing  up the face frame.   Maybe tomorrow, I can attach the assemblies to the sides?

What's for Lunch?
Confused


Attached Files Image(s)
   
Show me a picture, I'll build a project from that
Reply
#20
Supper.......supper time......
Winkgrin
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.