03-04-2019, 01:51 PM
Thank you everyone.
What's the consensus on hanging upper cabinets....gang 'em or individually?
|
03-04-2019, 01:51 PM
Thank you everyone.
03-04-2019, 01:55 PM
We always hung the uppers first that way you can use a dead man and get closer to the
03-04-2019, 03:25 PM
Thought about hanging the uppers 1st, but they wanted to be able to template for the counter tops ASAP, so the lowers went in 1st.
Dumber than I appear
03-04-2019, 03:37 PM
(03-04-2019, 11:41 AM)Phil Thien Wrote: Good timing for this thread. Don't pull the first cab completely tight against the top of the wall, or just back the screws off a bit.
Steve
Mo. I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24 The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints WaterlooMark 02/9/2020
03-04-2019, 08:07 PM
I've always hung uppers first, as in the video. Two things the video did not make clear. The ledger board can be used to show valleys and humps in the wall. I have a long level(6' or so) that I use to determine wall topography. A string line along the top of the wall will also highlight differences. I have seen installs where shims were installed vertically to minimize cabinet warpage.
Seldom have I had enough help to gang cabinets before installing. And, if there are only one or two cabinets, I use my third hand tool instead of a ledger. I even had a short third hand for using when the lowers were installed. Humorous story. A fellow called me asking what I would charge to help him hang cabinets. He wanted to do it himself and decided to use a drywall lift. He discovered the lift had to be tire to stay level and trying to tie it level and set cabinets on it was way more than he could do. I had done some work for his neighbor, so he called me. I decided to help and found out he was hanging the cabinets in a mobile home----meaning the screws had to go along the top, since vertical studs were not exactly 16" OC. He had no idea.
03-05-2019, 12:04 PM
I've always set the lowers first, with the counter top. It gives you a workbench. I would cover it with moving blankets.
Install the uppers, using my modified camper leveling jacks to set the upper on. Get the uppers hung, I would have a workbench (lowers) right there to lay my tools, assemble the door hinges and hang the doors. A place to lay your nail gun when installing the crown molding......etc......etc.....
Steve
Mo. I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24 The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints WaterlooMark 02/9/2020
03-05-2019, 06:28 PM
(03-04-2019, 10:20 AM)Dumb_Polack Wrote: Fellas,
03-06-2019, 06:52 AM
(This post was last modified: 03-06-2019, 06:53 AM by Snipe Hunter.)
(03-04-2019, 11:42 AM)Phil Thien Wrote: Also, I've heard of people hanging a ledger board, resting the bottoms of cabinets on that board, and shimming/screwing the cabinet in. That's how I do it. There should be no need to shim the bottom of a wall cabinet. Run a level 2x4 across the bottom, measured down from the lowest part of the ceiling. Set the first cabinet (usually a corner cabinet) and using a cabinet screw, attach the cabinet through the top nailing flange into a stud. I don't run the screw in tight. It helps if you mark the stud spot on the flange before lifting the cabinet. Hang them all that way. Then screw the faceframes flush with each other and shoot in all the rest of the cabinet screws tight into the studs. Then I patch the holes in the sheetrock left from mounting the 2x4. It's tedious but I always paint after the cabinets are in because something always seems to get scuffed up.
03-06-2019, 07:59 AM
(03-05-2019, 12:04 PM)Stwood_ Wrote: I've always set the lowers first, with the counter top. It gives you a workbench. I would cover it with moving blankets. Way back in the day when I was doing this kind of stuff, I recall we would do something very similar, using jacks set on the lower cabinets. As I recall, it worked pretty well.
If you are going down a river at 2 mph and your canoe loses a wheel, how much pancake mix would you need to shingle your roof?
03-06-2019, 11:24 AM
(03-06-2019, 07:59 AM)Bill Wilson Wrote: Way back in the day when I was doing this kind of stuff, I recall we would do something very similar, using jacks set on the lower cabinets. As I recall, it worked pretty well. Yes, worked for me. I used to install a lot of laminated backsplash sheets on the wall before hanging the uppers. No way to hang a ledger board on those, and I never enjoyed having to fill holes in someones new sheetrock.
Steve
Mo. I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24 The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints WaterlooMark 02/9/2020 |
|
Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.