Paper loading Performax 16 32
#6
  
I bought a Performax 16 32 from an auction at the local guild.  No manuals.  

Paper needed to be changed.  Having difficulty attaching paper to the closed end.  Tried YouTube.com, this forum, Google without success.  

I downloaded the "Operating Instructions" from OWWM.  The Operating Instructions provides the following on attaching paper.  

         "Install abrasives on the sanding drum as described on the "Sandpaper Attachment" insert."

The OWWM site does not have further instructions.  YouTube offerings discretely do not show paper installation at the closed end.  

After spending considerable time on this effort I now seek assistance.  

In addition to having no room to operate on the closed end, the clip on the closed end is different than the open-end clip.  

According to the manual for the JET version of the sander the drum is shown cut away at the inboard end to provide room to operate.  

any suggestion appreciated.  A copy of the "Sandpaper Attachment" insert may also be helpful of available.  

thx, Tom
Reply
#7
  Re: Paper loading Performax 16 32 by anwalt (I bought a Performax...)
Jet makes a special(optional) tool that makes paper changes much easier.
Waiting to grow up beyond being just a member
http://www.metaltech-pm.com
Reply
#8
  Re: Paper loading Performax 16 32 by anwalt (I bought a Performax...)
(08-13-2019, 04:42 PM)anwalt Wrote: I bought a Performax 16 32 from an auction at the local guild.  No manuals.  

Paper needed to be changed.  Having difficulty attaching paper to the closed end.  Tried YouTube.com, this forum, Google without success.  

I downloaded the "Operating Instructions" from OWWM.  The Operating Instructions provides the following on attaching paper.  

         "Install abrasives on the sanding drum as described on the "Sandpaper Attachment" insert."

The OWWM site does not have further instructions.  YouTube offerings discretely do not show paper installation at the closed end.  

After spending considerable time on this effort I now seek assistance.  

In addition to having no room to operate on the closed end, the clip on the closed end is different than the open-end clip.  

According to the manual for the JET version of the sander the drum is shown cut away at the inboard end to provide room to operate.  

any suggestion appreciated.  A copy of the "Sandpaper Attachment" insert may also be helpful of available.  

thx, Tom

Not sure if this is what you need but here's a link from the HGH Hardware website for the PERFORMAX 22-44 manual in PDF format.  Ought to be similar to the PERFORMAX 16-32

https://www.hghhardware.com/ASSETS/DOCUM...atalog.pdf
Reply
#9
  Re: Paper loading Performax 16 32 by anwalt (I bought a Performax...)
The holder on the head side is spring loaded. You need to feed the paper in while holding the clamp close to the drum. When you let it go it will move down and self tighten the paper. I usually have to cut a little off the paper at the motor end. The precut always seem to be a little long. Hope that helps. The first time you do this it can be very frustrating. Once you understand what you are supposed to do it does get easier. I have the manual somewhere. If you do not have what you need by tomorrow, I will try and find it. Could take pictures and post here. Or post here for me to check my pm I usually forget to check and could e-mail them to you. Probably won't check till late tomorrow afternoon. Busy till then.
Reply
#10
  Re: Paper loading Performax 16 32 by anwalt (I bought a Performax...)
I felt your pain until I got a Jet #98-0060 Tuftool. Bought from Amazon but a search there comes up empty. If you check other WW supply stores you'll turn one up. It sure takes the frustration out of changing media though it does have a bit of a learning curve.

Good luck,
g
I've only had one...in dog beers.

If hummus is made from Garbanzo beans, why isn't it called Garbanzus?
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)