Restoring Delta 20" bandsaw
#11
  
So I got this Delta 28-640 bandsaw for a song; now I'm trying to run down a trunnion for it. Can't find one ANYWHERE! Any ideas? The part number is Delta 1347491. I did hear in another board that the grizzly 21" trunnion may be the same; I called grizzly, but the return shipping is taking that out of the equation (if it doesn't fit). I could make a flat, non tilt able mount out of a chunk of white oak, but I'd like to find the trunnion, or repair the old one.

   
   
Now where is that chisel
#12
  Re: Restoring Delta 20" bandsaw by Smashedfinger (So I got this Delta ...)
Have you tried OWWM? They often have all of the old obscure machine parts and the knowledge to get the old machines working again.
#13
  Re: Restoring Delta 20" bandsaw by Smashedfinger (So I got this Delta ...)
Yes, I tried them first. Got a few tips anyway.
Now where is that chisel
#14
  Re: Restoring Delta 20" bandsaw by Smashedfinger (So I got this Delta ...)
(10-05-2019, 09:31 PM)stav Wrote: Have you tried OWWM? They often have all of the old obscure machine parts and the knowledge to get the old machines working again.

I think that saw is from Taiwan, so probably you wont get much out of OWWM. And I doubt they sold that many of that model so parts may be non existent. Your best bet might be to either try and fabricate one yourself of try and have one made. Or you could figure out a way to re-engineer the way the table mounts to the base, either tilting or fixed. You might want to take some better pix of the underside of the table and the mount on the saw and that might help folks make suggestions. Good luck with it.
#15
  Re: Restoring Delta 20" bandsaw by Smashedfinger (So I got this Delta ...)
Out of all the years I ever tilted a BS table, maybe once, I don't really see a need for one on a BS.
If no parts are found, I would go ahead and make a fixed base from a stable chunk of wood
Steve





Working on it Winkgrin





#16
  Re: Restoring Delta 20" bandsaw by Smashedfinger (So I got this Delta ...)
I was going to say I never have tilted my table- never.
"There are no strangers- only friends I haven't met.
#17
  Re: Restoring Delta 20" bandsaw by Smashedfinger (So I got this Delta ...)
And I frequently tilt mine! (joinery, bevel rips, staves, miters)  I certainly wouldn't be without a tilting table.

Bob
#18
  Re: Restoring Delta 20" bandsaw by Smashedfinger (So I got this Delta ...)
(10-05-2019, 11:43 AM)Smashedfinger Wrote: So I got this Delta 28-640 bandsaw for a song; now I'm trying to run down a trunnion for it. Can't find one ANYWHERE! Any ideas? The part number is Delta 1347491. I did hear in another board that the grizzly 21" trunnion may be the same; I called grizzly, but the return shipping is taking that out of the equation (if it doesn't fit). I could make a flat, non tilt able mount out of a chunk of white oak, but I'd like to find the trunnion, or repair the old one.

I'd say that OWWM is your best bet to find a replacement part. If it's available anywhere, someone over there will know about it. Just stay after them (be persistent) and someone will probably come through.

I'm not familiar with that trunnion, but failing getting a replacement part, do you have the piece that was broken off? If so it could be welded back in place.

Doug
#19
  Re: RE: Restoring Delta 20" bandsaw by Tapper ([quote='Smashedfinge...)
(10-08-2019, 12:19 PM)Tapper Wrote: I'd say that OWWM is your best bet to find a replacement part. If it's available anywhere, someone over there will know about it. Just stay after them (be persistent) and someone will probably come through.

I'm not familiar with that trunnion, but failing getting a replacement part, do you have the piece that was broken off? If so it could be welded back in place.

Doug

The saw was made in Taiwan, sending him to OWWM isn't going to end well for the OP.
#20
  Re: RE: Restoring Delta 20" bandsaw by jlanciani ([quote='Tapper' pid=...)
(10-08-2019, 12:24 PM)jlanciani Wrote: The saw was made in Taiwan, sending him to OWWM isn't going to end well for the OP.

OK, if it was made in Taiwan, there are probably only 8-10 other brands that were made in the same factory and use the same exact parts. Should be easy-peazy to find!  Yes Maybe start with Grizzly???

Doug


Forum Jump:


Users browsing this thread: 1 Guest(s)