Here's the new router table!
#11
Back in May in this post I asked the Woodnet brain trust their thoughts on using a tool cabinet as a router table base. After some discussion I decided to build a modified version of Norm's table to incorporate an Incra fence. After sketching out the changes I'd want to incorporate in Norm's design to utilize the Incra it became obvious to me that the tool cabinet was a more effective way for me to end up with a router table.

I bought the Craftsman cabinet at my local Lowes and ordered the top from Incra. Everything else I had bought used over the past year or two. A 3 1/4hp PC, Woodpeckers PRL1 and an Incra LS17 fence. Other than cutting the router hole and mounting the top, the only changes to the cabinet were to the drawers. Removing the top two didn't allow enough room for the router so I removed larger the third drawer and replaced it with the top shallow drawer. The slides were pop riveted in place so just drilled them out to remove, the cabinet was pre drilled so reinstalling was a snap. I fabbed an access door for the router using the pull from one of the drawers. 

Here's the completed table:
 
   

   

   

   

Comments welcome, thanks for looking.

g
I've only had one...in dog beers.

"You can see the stars and still not see the light"
The Eagles: Already Gone
Reply
#12
That turned out real nice. I kinda like it.
Steve

Missouri






 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply
#13
That turned out pretty dang cool!
Yes


I'm curious if you find it a bit low to work on comfortably?


Dave


Love the clean shop, too...
Winkgrin
"One should respect public opinion insofar as is necessary to avoid starvation and keep out of prison, but anything that goes beyond this is voluntary submission to an unnecessary tyrany, and is likely to interfere with happiness in all kinds of ways."
Reply
#14
Nice setup, when can I order mine 
Smile
Reply
#15
I think that worked out really well, nice!
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Reply
#16
That came out very well.  IIRC, I was skeptical when you first explained your plan.  But I think I think you pulled it off just great!

Enjoy using your new router table!
Reply
#17
(10-29-2019, 11:16 PM)Big Dave Wrote: I'm curious if you find it a bit low to work on comfortably?

Love the clean shop, too...
Winkgrin

Dave,
Thanks, I like a neat, clean workspace. It's 39" high, a little higher than workbench height but it feels comfortable. Will be giving it a workout over the winter so hoping I find it to be a good working height.

Looking for an Incra Wonder Fence add-on. If anyone has one laying around not being used give me a shout. Incra's lead time is 7-9 weeks. Grrrrr.

g
I've only had one...in dog beers.

"You can see the stars and still not see the light"
The Eagles: Already Gone
Reply
#18
very cool! Nice idea and well executed.. I may have to steal this idea
Smile
Reply
#19
That's a great rendition of your original design idea!

I'm probably wrong but ... won't the feed direction be from the back of this table?
i.e. the side with the dust port?
~Dan.
Reply
#20
Great idea but, if this is your shop it's way to neat & clean. I thought I'm a clean freak. But this is taking it to an all new level
Smirk
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.