Homegrown Spindle Sander Sleeves
#11
I'm thinking about an idea for a lathe mounted drum for sanding the inside of bracelets.     I'm also thinking about cutting and glueing my own sleeves.  I can get a custom size,  I can get whatever grits I want and sandpaper is cheaper.  Would there be an issue with 1/2" or so of overlap of the sleeve on the drum for the glueline?  I'd make sure the overlap was such that the top overlaps the bottom in the opposite direction the lathe travels.

Reply
#12
Overlap may cause a bump in sanding. Figure out how to eliminate that bump.
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply
#13
I know belt paper is butted together and then special tape applied and edges glued.  I have been wanting to make a long 8" belt sander on the lathe but can not figure out how to do it.
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Reply
#14
(12-04-2019, 01:08 PM)Stwood_ Wrote: Overlap may cause a bump in sanding. Figure out how to eliminate that bump.

i'm wondering how much of a bump and how bad it will be and what effect the bump will have on the sanding.   I'm also thinking about butting the edges and glue + carpet tape.  there will be less of a bump that way.

Reply
#15
Cut a slit in the drum and glue the paper in the slit?
"Oh. Um, l-- look, i-- i-- if we built this large wooden badger" ~ Sir Bedevere
Reply
#16
(12-05-2019, 09:00 AM)Large Wooden Badger Wrote: Cut a slit in the drum and glue the paper in the slit?

I thought about that. The drum is going to be wood with slits cut up it.  When I crank down my cone center, that will expand the drum and keep the sandpaper in place.  gluing them means I have to clean the drum each time.  Ive also thought about possibly finding carboard tubes or thin paper that wont have as big a bump if I overlap it, overlapping that and gluing sandpaper to those.

Reply
#17
I found this . https://www.amazon.com/dp/B07D1D97QJ/ref...WNrPXRydWU=

Reply
#18
(12-04-2019, 08:08 PM)crokett™ Wrote: i'm wondering how much of a bump and how bad it will be and what effect the bump will have on the sanding.   I'm also thinking about butting the edges and glue + carpet tape.  there will be less of a bump that way.

Butting should work I would think
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply
#19
(12-05-2019, 02:11 PM)crokett™ Wrote: I found this . https://www.amazon.com/dp/B07D1D97QJ/ref...WNrPXRydWU=

,,,,,,,,,,,,,,,,,,,,,,,,,,,
why not make a flap sander??????...Or a butt joint on a 45* angle to minimize any "bump".........
Often Tested.    Always Faithful.      Brothers Forever

Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Upset





Reply
#20
I used a piece of pvc pipe wrapped in psa sandpaper. No bump if you leave a slight gap.
VH07V  
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.