It followed me home..
#11
Can I keep it?
Winkgrin 
   
Was hanging up in an Antique Mall....screwed to an Oak plank, and labeled "Dowel Cutter".   A little rough..
Rolleyes 
   
Had some strange and some missing parts...
Uhoh
   
Price, including the Oak plank...$32.50
Confused plus a 3 block walk, both ways.   Plus sales Tax...
Angry

Might be worth the trip?
Confused
Show me a picture, I'll build a project from that
Reply
#12
(01-13-2020, 02:57 PM)bandit571 Wrote: Can I keep it?
Winkgrin 

Was hanging up in an Antique Mall....screwed to an Oak plank, and labeled "Dowel Cutter".   A little rough..
Rolleyes 

Had some strange and some missing parts...
Uhoh

Price, including the Oak plank...$32.50
Confused plus a 3 block walk, both ways.   Plus sales Tax...
Angry

Might be worth the trip?
Confused

Interesting Router Plane ...

With your turning skills, I see 2 knobs.. a little rehab and you'd have that pulling shavings!
Reply
#13
Video 
too bad about that broken stub of clamping bolt on the blade clamp.  By the time you finish removing the stub, the hole may be ready for retapping - and then you can retap to a standard thread and buy a thumbscrew at the hardware store.
Reply
#14
Nice find. I’ve been looking for one of those for a bit. Old tool hunting is pretty limited here.
Reply
#15
Lets see...soaked the clamp in PBBlaster for a while.   Then easy-out to remove most of the broken bolt..
   
And then cleaned the sole a bit....had to dig through the tap & die box...
   
And dig out a 1/4" x 20 tap, and a wrench...and a drill bit...drilled a bit..and then the tap..
   
Find 2 knobs that seemed to match each other...
   
Then went to work and the cutter...trying to get past the pits, straighten the edge, and get it sharp...
   
Bought the adjuster disc on ebay....and a pair of thumbscrews....which ran the cost of the plane up by $20 or so...regrind the tip of the bolt..
   
To the required point. assembled the plane, as best as I could..
Rolleyes 
   
Set up a test track...
   
Knifed 2 lines, marked with a pencil, deepened with a backsaw...and set the cutter...
Winkgrin 
   
And gave it a test drive..
   
Wheel gets here thursday mailbox....will see how it looks like, then,   Just under $55-$60 for this plane...so far...
Stay tuned...
Cool
Show me a picture, I'll build a project from that
Reply
#16
From tool to coat hanger to tool again. That's a good recovery!
Reply
#17
Adjuster wheel arrived today's mail....
Threaded rod needed it's threads "chased"....used the wheel...
   
Cranked it a few times, oiled the threads...
   
Should be all set to got to work....
Cool

Thanks for looking in..
Winkgrin
Show me a picture, I'll build a project from that
Reply
#18
Well done man!  Good save.


Cool
Mark Singleton

Bene vivendo est optimum vindictae


The Laws of Physics do not care about your Politics   -  Me
Reply
#19
The cutters for Lee Valley's router plane were designed to fit the Stanley, too, although you have to flip the adjuster wheel over, I think because they're longer.

Nice save.
Reply
#20
Cost of old Stanley router plane: $32.50 plus tax
Replacement knobs found in spare parts box: $0.00
Replacement adjuster disc and thumb screws: $20.00

Fun and satisfaction of bringing and old tool back to life: $ Priceless

Well done.
If women don't find you handsome, they should at least find you handy. -Red Green
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.