Recommendations on countersink drill bit set?
#11
Any suggestions on a decent set for woodworking? I know some use them for metal work but that's not my direction right now.

Thanks.
"Life is too short for bad tools.".-- Pedder 7/22/11
Reply
#12
The set from Snappy is priced right and works very well.
Reply
#13
I guess it depends on what you mean by countersink, but if you're just looking for just a countersink without the bit:

https://www.leevalley.com/en-us/shop/too...untersinks
Reply
#14
(04-13-2020, 10:24 AM)Scott W Wrote: Any suggestions on a decent set for woodworking? I know some use them for metal work but that's not my direction right now.

Thanks.

Many years ago I bought one of the Insty-Drive sets with 5 countersinks from Rockler.  Their countersinks have some real advantages; each size has three parts: shaft, bit, and countersink collar.  When you break a bit it is easily replaced. The bit travels all the way trough the shaft so you can shorten the depth two ways which lessens the risk of breaking the smaller size.  The countersink collar is adjusted with two set screws and has four flutes so I think is cuts quicker.  The bits are tapered, which most around here are not fans, but I am.

I seldom install a screw without countersinking so mine are very well used.  The bits have all been replaced a few times and I have been able to dress the flutes on the countersink collar with a diamond card.

The Insty-Drive set is about $90 now and in my opinion is not worth it, but I think the countersinks are the best that I have found.
"I tried being reasonable..........I didn't like it." Clint Eastwood
Reply
#15
I use several of the ones as linked above from Lee Valley.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Reply
#16
Yep, countersinks (without the drill bit) from LV or Weldon work great. Not sure about the LV's but the Weldons are also good on metal. Avoid the fluted ones.
Reply
#17
Since the title says countersink drill bit, I'll put my .02 in....

These are my go to countersink/drill bit set up.  Amana No-Mar from Tools Today

Amana No-Mar
"This is our chance, this our lives, this is our planet we're standing on. Use your choice, use your voice, you can save our tomorrows now." - eV
Reply
#18
Hard to beat Fuller products: I highly recommend them

W.L Fuller
Reply
#19
(04-13-2020, 10:24 AM)Scott W Wrote: Any suggestions on a decent set for woodworking? I know some use them for metal work but that's not my direction right now.

Thanks.

I bought a set of Fuller spiral tapered countersink bits years ago. I used them often as I was a carpenter and cabinet maker.
They are very good quality, a bit pricey compared to others that have straight bits, not tapered spiral bits like Fuller. I still use them but only once in awhile since I retired. I recommend them , have not used the others mentioned except for Snappy. My employer bought Snappy because they were inexpensive, he went back to Fuller about a year later. I do not think Snappy offers taper bits, that is what we needed generally.
mike
Reply
#20
I like these and got a discount throught woodnet.  I love the way they drill and CS.

https://www.holbren.com/carbide-tip-coun...drill-bit/

One comment:  The drill bits included are for the thread clearance, not body clearance.  I was working with some oak and twisted off a couple of screws before I got the sizes straight.
"Truth is a highway leading to freedom"  --Kris Kristofferson

Wild Turkey
We may see the writing on the wall, but all we do is criticize the handwriting.
(joined 10/1999)
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.