What does everyone use for sanding
#11
inside boxes or vases other places that are to deep or around a corner in a turning for a finger.

About half the time my fingers can not reach that far down or on the side so what do you use??
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Reply
#12
If I can't reach it, I don't bother trying.
Cellulose runs through my veins!
Reply
#13
(08-19-2020, 08:25 PM)Arlin Eastman Wrote: inside boxes or vases other places that are to deep or around a corner in a turning for a finger.

About half the time my fingers can not reach that far down or on the side so what do you use??

For going deep, sometimes I cut a slot in a dowel, insert sandpaper into the slot. It's not for everything, but at times the only thing that works for me.

Woodturners are the only people that will look.
Reply
#14
Thanks Hairy

How wide is the slot and how deep?  Also thank you for the pen blanks you sent.
Yes
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Reply
#15
(08-20-2020, 10:20 AM)Arlin Eastman Wrote: Thanks Hairy

How wide is the slot and how deep?  Also thank you for the pen blanks you sent.
Yes

Wide enough to just be able to slide the strip of sandpaper into and almost as deep as the sandpaper is wide. You don't want bare dowel sticking out the end.

I use that technique but also have a piece of Klingspor's sticky-back velcro near the end of a 1" dowel a foot long. That way I can use the velcro-back sanding discs and interface pads I use for OD sanding.
We do segmented turning, not because it is easy, but because it is hard.
Reply
#16
(08-19-2020, 08:25 PM)Arlin Eastman Wrote: inside boxes or vases other places that are to deep or around a corner in a turning for a finger.

About half the time my fingers can not reach that far down or on the side so what do you use??

Steve gave my answer.

However, if you think it matters,  https://www.walmart.com/ip/Starter-Rock-...9fd0f10e95  and put the grit INSIDE your corked vase.  Week ought to do.  

Or, alternatively, wire brush on long mandrel, followed by https://www.woodworkingshop.com/search.aspx?q=minimop I like them for detailing finger-stubbing, but reachable places.
Better to follow the leader than the pack. Less to step in.
Reply
#17
Thanks

I think the rock tumbler is out since I have one still.
Yes
Laugh

The mop looks very good tho.  I never thought of putting in dry sand before and turning at say 40 to 200rpm.
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Reply
#18
A major nice thing about segmented turning is that you can turn and sand the inside as you assemble the rings if you choose to. You just need to be careful of wall thickness to keep chatter and explosions down, not that it has ever happened to me of course.

(The difference between doctors and turners is that turners can burn their mistakes.)
We do segmented turning, not because it is easy, but because it is hard.
Reply
#19
(08-20-2020, 09:27 PM)SceneryMaker Wrote: A major nice thing about segmented turning is that you can turn and sand the inside as you assemble the rings if you choose to. You just need to be careful of wall thickness to keep chatter and explosions down, not that it has ever happened to me of course.

(The difference between doctors and turners is that turners can burn their mistakes.)

Maybe bad Dr. burn paperwork.
Yes
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Reply
#20
(08-20-2020, 07:30 AM)hairy Wrote: cut a slot in a dowel, insert sandpaper into the slot.

Put the dowel in a drill. 

I don't function well before my 2nd cup of morning coffee  
Sleep
Sleep
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.