Using Earlex 5500 to spray paint
#16
@John,

What is the maximum you will thin a latex paint?

Have you ever used anything other than water?  I've heard about windshield washer fluid.
Reply
#17
(10-27-2020, 08:06 AM)rwe2156 Wrote: @John,

What is the maximum you will thin a latex paint?

Have you ever used anything other than water?  I've heard about windshield washer fluid.

I had to thin SW's ProClassic 18% to spray it with my 1.8 mm N/N gravity feed gun, back before I got the pressure assisted gun.  It worked, but it's not something I would want to do regularly because it tends to run more easily which is no surprise.  It doesn't look quite the same either though I'm hard pressed to explain in what way.  

When I have to thin stuff I typically start with plain tap water and 3% of BM's Extender, using enough water to get the viscosity down to 300 seconds or less.  Extender can make a marginal spray pattern look very good in about 5 minutes because it lets it flow out more before setting up.  

I've never heard about using windshield washer fluid to thin a waterbased paint.  I have no idea why that would be a good thing.  Extra surfactants and alcohol don't seem like things I would want to add.  For sure I'd try it with a small batch on a test panel if I did want to evaluate it.  

Paints that have sprayed best for me are ones that are an oil emulsion - BM's Advance and SW's Emerald Urethane Trim paint.  Both spray well once I thinned them to 300 seconds and flow out beautifully.  The Emerald Urethane Trim paint dries a lot faster and that's the one I now use most.  And there are other ways to get an opaque finish besides using paint.  Both GF and TC and Lenmar sell pigmented WB lacquer products.  They have viscosities less than 200 seconds and can be sprayed with a gravity feed gun with a little thinning, although a pressure assisted one makes the job easier.  Maybe it's just symantics, paint vs. pigmented lacquer, I don't know.  But the lacquer products seem to have lower viscosity and spray more easily, probably because they are targetted for spraying whereas paint is formulated for manual application or airless spraying.  

FWIW, Lenmar's Duralaq-WB White lacquer sprays beautifully with my pressure assisted gun, as easily as most clear coats, and looks gorgeous - like it came out of a factory.  And it can be tinted to a whole range of colors, too.  

John
Reply
#18
John,

Great post. Not to get off the OP’s topic but would you consider using Duralaq’s WB lacquer for a new set of kitchen or bath cabinets if wanting a white finish?


Reply
#19
(10-28-2020, 01:58 AM)Kansas City Fireslayer Wrote: John,

Great post.  Not to get off the OP’s topic but would you consider using Duralaq’s WB lacquer for a new set of kitchen or bath cabinets if wanting a white finish?

No, definitely not.  It's easily damaged with ammonia containing cleaners.  But I definitely would consider Lenmar's MegaVar white precat lacquer if I could use solvent based products.  That product is KCMA rated.  Since I only use WB products, besides shellac, I'd probably use GF's Enduro White Poly, either alone or with a topcoat of Clear Poly.  Honestly, however, I have not found a bomb proof WB white finish for kitchen cabinets.  SW's KemAqua Plus White might be a good option since it's KCMA rated, but I haven't used it.  I'm pretty sure some of SW's Sayerlack products would work well, too, but haven't used those either because the last I looked the minimum was 5 gals.  

John
Reply
#20
(10-28-2020, 01:58 AM)Kansas City Fireslayer Wrote: John,

Great post.  Not to get off the OP’s topic but would you consider using Duralaq’s WB lacquer for a new set of kitchen or bath cabinets if wanting a white finish?

(10-28-2020, 12:24 PM)jteneyck Wrote: No, definitely not.  It's easily damaged with ammonia containing cleaners.  But I definitely would consider Lenmar's MegaVar white precat lacquer if I could use solvent based products.  That product is KCMA rated.  Since I only use WB products, besides shellac, I'd probably use GF's Enduro White Poly, either alone or with a topcoat of Clear Poly.  Honestly, however, I have not found a bomb proof WB white finish for kitchen cabinets.  SW's KemAqua Plus White might be a good option since it's KCMA rated, but I haven't used it.  I'm pretty sure some of SW's Sayerlack products would work well, too, but haven't used those either because the last I looked the minimum was 5 gals.  

John

I'm using the Duralaq WB "lacquer" (its an acrylic) for interior doors and it looks great. These should only ever get a damp cloth to remove fingerprints around the knob, etc. 

Two interesting data points:

I spray outside and piddled a bit of the material on the driveway back in June I think. It is still there. Of course this is just outside sun and rain, I don't clean the driveway with ammonia but interesting that it has been durable like that.

Second, I clean the gun with household sudsy ammonia mixed about 50:50. It really doesn't touch the dried stuff without some additional mechanical abrasion. Of course I wasn't measuring coating thickness before and after. But using the sudsy ammonia to wipe down the cap and nozzle still required some elbow grease. Didn't try soaking.
Don't sweat the petty things and don't pet the sweaty things. -- G. Carlin
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.