Finish sanding process for oil poly?
#11
Question 
I don't have a proper finishing booth so dust and bugs find their way on to my finish. 

Last coat is down but had dust nibs and several gnats. I hit it lightly with 600g and now it's smooth but there are scratches here and there

What further steps do I need to take for a smooth, satin finish?
Semper fi,
Brad

Reply
#12
(05-19-2022, 06:57 AM)®smpr_fi_mac® Wrote: I don't have a proper finishing booth so dust and bugs find their way on to my finish. 

Last coat is down but had dust nibs and several gnats. I hit it lightly with 600g and now it's smooth but there are scratches here and there

What further steps do I need to take for a smooth, satin finish?

0000 steel wool and soapy water or paste wax will give you a nice satin sheen.  If it's oak I'd use a synthetic pad or brass wool instead of steel wool, however, unless it's very well sealed.  Rub only with the grain. 

John
Reply
#13
John, you seem extremely knowledgeable on finishing (along with many other woodworking related topics).  Curious what you think of Behlen's Wool Lube for something like this?
Reply
#14
(05-19-2022, 09:17 AM)jteneyck Wrote: 0000 steel wool and soapy water or paste wax will give you a nice satin sheen.  If it's oak I'd use a synthetic pad or brass wool instead of steel wool, however, unless it's very well sealed.  Rub only with the grain. 

John


Will that remove the 600g marks I have?
Semper fi,
Brad

Reply
#15
I have used Behlen's Wool Lube and 0000 steel wool after 400g sanding so it should definitely take out your 600g marks.
Reply
#16
It worked, folks, thanks!  I put a strip of 0000 steel wool on my ROS, applied Johnson's Paste Wax to it, and attacked it. 

Then I let it sit for twenty minutes and then buffed it out.  Worked great. 

Thanks, again!
Semper fi,
Brad

Reply
#17
(05-19-2022, 11:05 AM)BrentDH Wrote: John, you seem extremely knowledgeable on finishing (along with many other woodworking related topics).  Curious what you think of Behlen's Wool Lube for something like this?

Work at anything long enough and a few bits of wisdom eventually stick.  I've never used Behlen's Wool Lube but I think it would work well.  I've always either used paste wax or soapy water because I'm cheap and have both on hand.  

John
Reply
#18
(05-20-2022, 06:26 AM)®smpr_fi_mac® Wrote: It worked, folks, thanks!  I put a strip of 0000 steel wool on my ROS, applied Johnson's Paste Wax to it, and attacked it. 

Then I let it sit for twenty minutes and then buffed it out.  Worked great. 

Thanks, again!

How did you hold the steel wood to the ROS?  Is there a type now with hook and loop?  Anyway, glad it worked out.  

John
Reply
#19
(05-20-2022, 09:31 AM)jteneyck Wrote: How did you hold the steel wood to the ROS?  Is there a type now with hook and loop?  Anyway, glad it worked out.  

John

I unrolled a piece of it and pressed it to a velcro pad.  Once it was spinning, I would periodically pull off the parts that tried to get flung off until I was left with a layer of steel wool under the pad that remained.
Semper fi,
Brad

Reply
#20
(05-19-2022, 06:57 AM)®smpr_fi_mac® Wrote: I don't have a proper finishing booth so dust and bugs find their way on to my finish. 

Last coat is down but had dust nibs and several gnats. I hit it lightly with 600g and now it's smooth but there are scratches here and there

What further steps do I need to take for a smooth, satin finish?

Pumice should equalize the surface at satin.  

Rottenstone for gloss.
Better to follow the leader than the pack. Less to step in.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.